Showing results: 2611 - 2625 of 3660 items found.
-
F10A -
FLC Electronics Inc
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
F20A -
FLC Electronics Inc
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
DeltaTRAK
The Temperature/Humidity/Dew Point Circular Chart Recorder uses a red pen to track temperature and a blue pen to track humidity, permanently recording these measurements on a 6-inch (165mm) diameter paper chart. Power is supplied to the temperature recorder through a 110V AC 50/60 Hz plug-in adapter for Model 14013 and a 220V AC adapter for Model 14014. External power may be supplied from any 12V DC source such as automotive, marine or other battery.
-
MFG-8202 -
MCH Instruments Co.,Ltd.
Features:• Low distortion, high stability• Linear and logarithmic sweep function• Sweep time and width adjustable• External Voltage Control Frequency (VCF)• Internal & external modulation (AM/FM) with modulation control• Output signal compatible with TTL/CMOS• Seven types of waveforms such as sine, square, triangle and ramp• 5W power output (ONLY for model no with “B”)• DC offset and 40bD attenuation can be applied to main output signal• Built-in frequency meter 0.1Hz~30MHz
-
MFG-8205 -
MCH Instruments Co.,Ltd.
Features:• Low distortion, high stability• Linear and logarithmic sweep function• Sweep time and width adjustable• External Voltage Control Frequency (VCF)• Internal & external modulation (AM/FM) with modulation control• Output signal compatible with TTL/CMOS• Seven types of waveforms such as sine, square, triangle and ramp• 5W power output (ONLY for model no with “B”)• DC offset and 40bD attenuation can be applied to main output signal• Built-in frequency meter 0.1Hz~30MHz
-
ADCFN10-AC – HPC -
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
RFM-ADAFF22 -
Sundance Multiprocessor Technology Ltd.
The RFM-ADAFF22 is a two channel Analog to Digital and two channel Digital to Analog mixed converter FMC which complies with VITA 57.1-2010. Each AD channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Each DA channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A.
-
RFM-ADAFF62 -
Sundance Multiprocessor Technology Ltd.
The RFM-ADAFF62 is a six channel Analog to Digital and two channel Digital to Analog mixed converter FMC which complies with VITA 57.1-2010. Each AD channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Each DA channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A.
-
BCD250 -
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
TF900 Series -
Aim-TTi
Frequency, period, pulse width, frequency ratio, duty cycle, and event counter modesDC to 3000 or 6000MHz range, 0.001mHz resolutionHigh impedance measurement up to 125 MHzAC or DC coupling, 1M/50Ohm selection, polarity invertSwitchable attenuator, threshold controlNoise filter for low frequency measurementsSelectable measurement time; display hold functionLarge 10 digit display with full range of annunciatorsInternal rechargeable batteries for portable useUSB interface provides full remote control and readback
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
McPherson, Inc.
Solar blind detector for operation in the 1 to 180 nanometer region. It is encased in a vacuum tight housing for vacuum operation. The Model 425 is ideal for measurements in the Extreme and Vacuum UV (EUV and VUV) where the solar blind feature eliminates potential interference from long wavelength ultraviolet and visible light. It may be operated in pulse-counting mode or DC. The CEM is also available with coatings like Cesium Iodide or Magnesium Fluoride to enhance response in different energy regions.
-
Columbia Research Laboratories
Columbia Research Labs offers our standard Inclinometer System and our Differential Inclinometer System. The standard system includes a temperature compensated force balance inclinometer in conjunction with a power module and convenient digital display. It is available with either AC or DC Power supply input. The Differential System allows the customer to match the slope of two remotely located surfaces. The readout can be set to indicate the absolute tilt of either sensor or the differential angle between them.
-
DLAP-401-Xavier -
ADLINK Technology Inc.
- Deep learning acceleration with NVIDIA Jetson AGX Xavier- Compact system 150(W) x 145(D) x 85(H) mm- 3x USB 3.1 Gen1 lockable type, 2 GLAN, 1 Type C USB 3.1 OTG- Internal function expansions by M.2 E key 2230, M.2 B key 3042- 24V DC input- Additional storage by M.2 B key 2242
-
AWG18 -
APPLICOS
The AWG18 is an 18 bit Arbitrary Waveform Generator for high-speed / high resolution waveform generation. This module features two dedicated signal paths. A DC to 100 MHz path which is optimized for accurate time domain and frequency domain measurements up to 30 MHz. And a dedicated AC path optimized for signals between 10 MHz to 100 MHz. In combination with the built-in filters it features a typical harmonics level of better than -80 dBc for the whole range.