Showing results: 676 - 690 of 3660 items found.
-
PCH2400 5000 Series -
Twintex Electronics Co., Ltd
The PCH series are high power output Switching DC power supply with rated power from 600W toW. The PCH series adopts ZVZCS PWM technology, which greatly reduces switching consumption and therefore facilitates switching function with high efficiency and high stability.
-
LDH400 Series -
Aim-TTi
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
DC3 -
Hilevel Technology, Inc.
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
LAB / HPL -
ET System Electronic GmbH
*Output from 5kW to 10kW*Output voltage up to 600V*Output current up to 500A*Dimensions: 19 "x 3 U x 620mm*Integrated load; voltage controlled*For 2-quadrant operation*Compact design*Low noise development for pleasant work in the immediate vicinity of the device
-
-
Process101A -
MadgeTech, Inc
The Process101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art data logging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
Volt101A -
MadgeTech, Inc
The Volt101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art data logging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
IT-M3100 Series -
I-TECH Electronic Co., Ltd
IT-M3100 series breaks through the traditional tech limits, in the ultra compact size of only 1U Half-Rack, the unit can not only output high power, but also has high performance and versatility. It supports the master-slave parallel mode. The full range of models support multiple stacking and parallel connection by handily designing "leg" plug-in. Fit with rack mount kit to achieve the perfect use.
-
USSVM2 -
Alpha Lab, Inc.
The meter measures the magnitude and polarity of static charge on objects or surfaces. The sensor is calibrated for measuring a surface at 1" from the end of the sensor. On metallic or conductive surfaces, the meter measures the voltage on the surface. (As with any electrostatic voltmeter, the displayed reading depends somewhat on the size of the object being measured and the distance between the object and the sensor.) On insulating surfaces, "voltage" is not a well-defined number. In this case, the meter reads a number proportional to the static charge present.
-
FLIR CM46 -
Teledyne FLIR
The FLIR CM46 clamp meter is designed for commercial and residential electricians. Featuring both AC/DC measurement, the meter is equipped with a bright backlit display for use inside electrical panels. Accu-Tip™ technology delivers amperage measurements on smaller-gauged wires more accurately — to a tenth of a digit. The meter also offers MAX/MIN/AVG recording; measures DCµA, temperature, capacitance, and frequency; and has electrical field detection to help you determine voltage presence and relative strength of the field.
-
MPS-D+ series -
Matrix Technology Inc.
Voltage stabilitySource effect CV≤0.01%+2mVLoad effect CV≤0.01%+2mVRipple and noise CV≤1mV(rms)CC≤5mA(rms)Voltage temperature coefficient 150ppm/°CCurrent stabilitySource effect CC≤0.2%+2mALoad effect CC≤0.2%+5mACurrent temperature coefficient 500ppm/°C
-
2781 / 2781 T (True RMS) -
Kusam Electrical Industries Limited
* Jaw opening dia - cable of 40mm * 3¾ digit (4000 counts) LCD for accurate reading.* Overload protection on all ranges. * Data-hold facility * DCA zero button for accurate reading* Low battery indication* Auto power off* Accessories : Test leads, carrying case, manual, battery installed
-
44LS1 -
North Atlantic Industries
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
Series KLP -
Kepco, Inc.
The KLP is an entirely new laboratory grade power supply in which the voltage/current limits are automatically recalculated, forming a constant-power hyperbolic-shaped boundary between the voltage and current modes. This curve, which replaces the single max-power operating point of conventional power supplies, provides the user with a greatly expanded choice of maximum power volt-ampere combinations as illustrated in the diagram by points A to B to C. The constant-power limit of the KLP is 1200 watts.
-
44KS3-02 -
North Atlantic Industries
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.