Showing results: 556 - 570 of 785 items found.
-
VistaScope -
Anfatec Instruments AG
VistaScope is a unique AFM with flexible & full optical access to the tip/sample region. The VistaScope controller comes equipped with multiple lock-in amplifiers that allow patented photo-induced force microscopy (PiFM) and patented demodulation technique for background suppressed scattering scanning near-field optical microscopy (s-SNOM). It provides the ultimate capability in tip-enhanced optical microscopy as well as co-located AFM and far field optical techniques such as confocal Raman and confocal photoluminescence.
-
79-11 -
Testing Machines, Inc.
Crease and Board Stiffness testing is useful to industries of carton board, paper, printing and packaging. The relationship between board stiffness and crease recovery (spring back) is an important factor in the performance of cartons on high speed packaging machines and in manual folding. It is crucial to have the creases in boards correct and uniform. The crease recovery (spring back) can result in forces, which distort the carton or cause stresses to be applied to closures, which reduce their effectiveness.
-
M-011 -
Physik Instrumente GmbH & Co. KG
M-011 ultra-high-precision magnetically-coupled stages use the force of integrated magnets to preload the bearing. This magnetic preload results in extremely uniform and smooth motion with minimum friction. Unlike conventional stages, where two bearings with limited parallelism guide the carriage (inducing runout and rotational errors) in M-011 stages, only one of the two linear bearings has a guiding function (V-groove) while the second bearing is for support only (U-groove).
-
Columbia Research Laboratories
Columbia's Biaxial Inclinometers use the same force balance accelerometer technology used in our single axis inclinometers. These Biaxial Inclinometers are used in applications where dual axis tilt measurements are required. The SI-702B series is intended for use in applications such as platform stabilization, surface mapping and measuring tilt angles in remote locations. The SI-701AI series, is designed with an output circuit configuration made for use in 4-20mA data transmission systems.
-
ZET 7110 -
ZETLAB Company
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
900-355 -
Phase II Plus
Load Cell driven system provides precise control of test force application Direct digital reading Engineered to obtain highly sensitive and accurate readings Perfect for laboratories, workshops, tool rooms, inspection labs, etc. Measuring Range: 8-650HBW
-
PHD-4001A -
High Power Pulse Instruments GmbH
*Electrically isolated probearm kit for VF-TLP, TLP, HMM, HBM force and sense probingbased on the GGB Picoprobe Model 10 replacement probe tips*Buried coaxial cable channel for thermo-chuck in isolated chamber temperature measurements*Compatible with GGB Picoprobe Model 10 replacement probetips*Compatible with all standard micropositioner interfaces*High precision rotation of the probearm by backlash-free 80:1 gear*Rugged stainless steel design*SMA connectors
-
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
Elbit Systems of America®
Installed on a variety of platforms, the HeliC3om™, Advanced C4I and Mission Management System, is combat proven and developed by active pilots whose first-hand combat experience is incorporated into all facets of the system. Our technology keeps all elements updated in real time with inputs from networked C4I sources. Pilots and crew easily receive and transmit video and data to/from all forces while updating maneuver, air, and naval units.
-
SCR ELEKTRONIKS
SCR Elektroniks make CORD SWIVELING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis,20 Revolutions clockwise & 20 Revolutions anti-clockwise.
-
AC/DC Module -
COMSOL, Inc.
The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.
-
ZET 7111 -
ZETLAB Company
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
Q-Card
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
Modus Test, LLC
Instrumentation• 16,128 Kelvin ChannelsApplications• Cres Test Characterization For Test Sockets / Probe Heads / Connectors• Package Testing / Qualification• Device Opens / Shorts Testing• MTC Compatible For Integrated Cycling / Stepping / Force Measurement• MTC-TC Compatible For Hot/cold Thermal Chamber Characterization
-
infraTest Prüftechnik GmbH
The device consists of a sturdy frame with step motor drive, which moves the water box with the Scherbüchsenunterteil. For the measurement of shear force, shear path and settlement electronic transducers are provided. The device control with measurement data acquisition takes place via PC with software PROPRESS.