Showing results: 376 - 390 of 787 items found.
-
Shimadzu Corp.
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
L-3 Cincinnati Electronics
Multi-sensor systems for perimeter surveillance, security and force protection are available in a variety of lens and sensor combinations, and can be customized to meet any mobile or stationary mission requirement. These systems may be operated independently or in a fully integrated sensor network.
-
VP460 -
Abaco Systems Inc
The VP460 is designed to enable customers to begin development of their next generation systems using revolutionary new processor technology. It is in alignment with the SOSA™ Technical Standard to provide the interoperability required by the US Air Force, Army and Navy.
-
ECO-Vibe neo -
EMIC Corporation
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
TPA-95 -
High Power Pulse Instruments GmbH
*Flexible pulse force, pulse sense combined TLP probe arm kit based on TPA-95L and TPA-95R*Compatible with typical standard micropositioner mechanical interfaces*4.7 kΩ pulse sense voltage divider, which results in a voltage transfer ratio of (4700 + 50)/50 = 95 : 1 into 50 Ω*Variable probe pitch configuration*1 m flexible 50 Ω cables with SMA connector for pulse sense*0.1 m flexible 50 Ω cables with SMA connector for pulse force*Tungsten probe tips*Can be used for chuck backside grounded TLP measurements
-
Instron
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
FFF -
Wyatt Technology
Is a separation technique where a field is applied to a fluid suspension or solution pumped through a long and narrow channel, perpendicular to the direction of flow, to cause separation of the particles present in the fluid, depending on their differing "mobilities" under the force exerted by the field.
-
Electrogrip Company
Electrostatic chucks are the most reliable solution for gripping delicate, microfabricated metal foils - even in air. These chucks induce no distortion, are easily cleaned, are amazingly robust, economically priced, and exhibit uniform grip forces over their entire area.
-
STMicroelectronics
ST’s FingerTip® supports other advanced features thanks to the multi-mode sensing technology such as gloves, thick cover, water, custom gestures, grip rejection, proximity detection, force sensing and fast report rate for gaming applications.
-
ViProbe® -
FEINMETALL GmbH
FEINMETALL ViProbe® is based on the original "buckling beam" technology providing a truly vertical contact.The beams are precisely held in position by guiding plates. The low deviation of force versus overdrive ensures a high insensitivity to planarity differences.
-
Argon ST
We design and build discrete systems and complete solutions for communications, ISR and protection of forces. Our products include reconnaissance, communication and navigation systems; geo-location systems; EW systems; threat warning systems and adversary emulation systems.
-
Shimadzu Corp.
Clip grips are easy-to-use and applicable for low force tensile testing of materials such as yarn and plastics. Both 10 N (2.2 lbf) and 50 N (11 lbf) clip grips have flat metal grip faces.
-
EBB SERIES -
Transducer Techniques, Inc
The EBB Series is a economical low capacity bending beam load cell suitable for use in a variety of industrial and OEM force measurement and weighing applications. It is made of an aluminum alloy and comes in 1, 2, 5 and 10 kilogram ranges.
-
Kokusai Co., Ltd.
This system has a performance performance system that simulates the force applied from the vehicle side to the tire and the influence exercised from the road side by a high speed transfer unit and a high response torque generator with a power circulation system.
-
IMADA, Incorporated
Desktop force/displacement testers record both force and displacement. Programming is facilitated by the unique program dial using plain language menu screens.The jog movement moves the sensor .05mm for each click of the program dial (under no load).