Showing results: 1486 - 1500 of 1725 items found.
-
Circuit Check, Inc.
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
45-542-001 -
Pickering Interfaces Ltd.
The 6U PXIMatrix Module 45-542 is a very high density electro-mechanical relay matrix available in 132x8 format with 1 pole switching. Typical applications include signal routing in Functional ATE and data acquisition systems. The matrix is constructed using high reliability 2A electro-mechanical relays, offering >10e8 operations (under low power loads) to give maximum switching confidence with long life and stable contact resistance.
-
CM8 -
North Atlantic Industries
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
PCE Instruments
At PCE Instruments you will find a professional quality gas detector / gas detection instrument for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
-
PCE Instruments
At PCE Instruments you will find a professional quality gas meters for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2 m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
-
RMO TT Series -
Amperis sl
The Tap Changer Analyzer & Winding Ohmmeter of the RMO-TT series is designed for winding resistance measurement of inductive objects, and for a tap changer analysis. The RMO-TT series is based on the state of the art technology, using the most advanced switch mode technology available today. The RMO-TT instruments are accurate (0,1%), powerful (up to 100 A) and still portable. The Instruments generate a true DC ripple free current with automatically regulated measurement and discharging circuit. RMO-TT instruments can perform a simple, quick and reliable transformer on-load tap changer condition assessment. This series of instruments enable measurements of a winding resistance in every tap position, current ripple values (percentage of a current drop during a tap change) and transition times during the tap changes. Problems with a connection, contacts, and selector/diverter switch operation (tap change with interruption) can be detected with these measurements.
-
Partikel-Analytik-Messgeräte GmbH
PA Rhometer measures the density, weight and volume fractions of dispersions. The device uses the oscillating tube technology: it measures the vibration frequency difference between pure solvent and dispersion. It features an integrated microcontroller which computes all of the data onboard. It can feed it directly into PA Field ESA and/or PA Fast Sizer, thus enabling online and batch measurements of processes and samples with unknown or changing particle concentration. Alternatively, the device can be used as a stand-alone unit and the information is exported into an Excel sheet. The device features a sturdy design, suitable for both lab and industrial applications. All surfaces which come in contact with the sample are glass, Teflon or POM and all connectors are made of stainless steel. It can be used as a flow-through unit or fed manually. The user-friendly software and easy to follow SOPs do not require highly trained personnel and ensure reproducible results.
-
R1L-BR -
TEGAM Inc.
The R1L-B series Ohmmeter/Bonding Tester is a digital microohmmeter designed to measure resistances from 10 to 20 . It is used in applications such as metal bonding, switch, circuit breaker, circuit resistance and other contact and connection resistance tests as well as higher resistance measurements for circuit analysis and resistor testing up to 20 . The instruments utilize the four-terminal, Kelvin technique to eliminate errors caused by the resistance of the leads. Resistance readings are viewed on a 3 1/2 digit display,
-
Megger Group Ltd.
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
778572-85 -
NI
10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module —The PXI‑2585 is a high‐power PXI multiplexer switch module that is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing. It is configured as a 10x1 multiplexer with both low contact resistance and high isolation voltage. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Wuhan Sunma Technology Co., Ltd.
Optical Multimeter integrates both an optical power meter module and an optical light source module and can perform closed-loop tests by using both modules but work individually. It is specifically designed for technical support personnel to test a variety of instruments with a single meter and thus satisfy the user by providing a choice of greater convenience and more advantages. Contact us at Sales@SunmaFiber.com Buy other fiber optic products on SunmaFiber. Save your money & time right now!
-
40-521-021 -
Pickering Interfaces Ltd.
An ultra high density matrix module is configured as a 24x8, this range is availablein a choice of reed relay formats: 1-pole (shown here), 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisitionsystems. These PXI matrix cards are constructed using high reliability RutheniumElectro-Plated Reed Relays, offering >10e8 operations to give maximum switchingconfidence with long life and stable contact resistance.
-
40-520-205 -
Pickering Interfaces Ltd.
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
