Showing results: 2086 - 2100 of 3346 items found.
-
Comptus
Comptus Barometric pressure sensors utilize an integrated silicon, absolute pressure sensor with internal temperature compensation. The sensor is mounted to the signal conditioner board. A 3/16 inch diameter tube may be attached to the sensor to provide remote pressure sensing. The output of the sensor is scaled to provide the desired output signal.
-
GASERA ONE SHED -
Gasera Ltd.
Evaporative losses from the fuel system are tested for vehicle certification. GASERA ONE SHED allows direct monitoring of evaporative emissions as part of the qualification testing procedures for vehicles. The GASERA ONE SHED’s photoacoustic technique is approved by the Environmental Protection Agency (EPA) and the California Air Resources Board (CARB).
-
CY7C65213 -
SparkFun Electronics
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running.
-
A2818 -
CAEN S.p.A.
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
40-966-096-F -
Pickering Interfaces Ltd.
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
40-966-096-M -
Pickering Interfaces Ltd.
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
SIU36 -
North Atlantic Industries
The SIU36 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU36 leverages NAI’s 3U boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
68ARM1 -
North Atlantic Industries
NAI’s 68ARM1 is a 3U VPX ARM® Cortex®-A9-based, Single Board Computer (SBC) that can be configured with up to three smart function modules. Ideally suited for rugged defense, commercial aerospace, and industrial applications, the 68ARM1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
Dynamic Engineering
The PMC compatible PMC-Parallel-485 design adds 32 [RS-485 /RS-422] differential IO lines to one slot of your carrier board. 2 additional differential pairs are available for a clock & clock enable. The signals can be used to capture data with an external reference or programmed to be references for the rest of the system.
-
Reltech Limited
Preconditioning is performed prior to package level reliability testing to simulate the effects of board assembly on non-hermetic devices where moisture may have been absorbed during normal storage. The subsequent exposure to high temperature during infra reflow assembly can cause internal damage such as “pop corning” and delamination.
-
OCP NIC 3.0 -
UNH IOL
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
BusPro-I™ -
Corelis, Inc.
The BusPro-I has all the power, flexibility, and features you need to monitor and debug the I2C bus circuitry on your board. The BusPro I2C can be used to monitor and log I2C bus traffic in real-time, generate I2C transactions to communicate with peripheral components on the bus, and in-system program I2C compatible EEPROMs.
-
National Technical Systems
There are generally two types of bending tests. Three-point bend and 4-point bend. The materials that are tested using the flex test method vary from metal, plastic, wood, laminates, particle board, dry wall, ceramic tile, to glass. Bending tests vary greatly based on the product being tested.
-
SEMIFLOW CO.65 -
SONOTEC GmbH
SEMIFLOW CO.65 non-contact clamp-on flow sensors are ideal to measure abrasive, adherent, corrosive, and ultra-pure liquids on rigid plastic tubes and pipes used in the semiconductor industry. Equipped with an integrated electronic unit, they function as a complete flow meter in the size of a small transducer without an external board or transmitter.
-
Kontron
This 5 slot Hartmann VPX 4U desktop system chassis provides a portable packaging solution for high-performance processors on a full mesh backplane topology. The 42HP wide desktop enclosure for vertical mounting of boards is outfitted with a 300W ATX power supply and a 1U fix bottom mounted fan tray.