-
product
Intelligent CPCI Quad Industry Pack Carrier
CPCI-6713-4 IP
The board consists of private SDRAM and Flash memory attached to the 300 MHz TMS320C6713B DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is availablefor downloading programs into a non-volatile memory. A PCIbus connector provides the interface to the host computer. A serial port is available for debugging.
-
product
12-bit, 100KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3001-4
4 single-ended or 2 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.T...show more -
product
Reflective Memory
VME-5565
The VME-5565 Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board can be configured with either 64 Mbyte or 128 Mbyte of onboard SDRAM. The local SDRAM provides fast Read access times to stored data.
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24V, LACQUERED
APCI-1500-LAC
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
product
FMC Card with DisplayPort Input and Output
TEF0007-02A
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0007 is a DisplayPort 1.2 compatible FMC card with data rates up to 5.4 Gbps and sink and source DP connector. SN65DP159 is used as DP Retimer and SN75DP130 as DP Redriver to connect sink and source to on board Kintex-7 FPGA.Image stream over FMC can be realized over 4 MGTs (only 1 available on LPC) and 34 differential IOs (LPC compatible).
-
product
Power Interface and Prototype PXI Card
GX7404
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
product
Test Fixture Kits
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
product
PXI Breadboard Module, 2-Slot, 9-Pin D-Type
40-220A-702
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
PCI/PCIe I/O & Comm Board
76C2
NAI’s 76C2 is a PCI/PCIe multifunction I/O and communication board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
6U VME Multifunction I/O Board
64G5
NAI's latest generation 6U VME multifunction I/O and communications board, the 64G5, can be configured with up to six intelligent function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance, board delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
product
7" Capacitive Touch Panel Overlay
The LattePanda 7-inch touch panel overlay uses capacitive touch technology and multi-touch to bring you a truly interactive experience. Simply overlay the panel on your LattePanda 7-inch display, power the board, and you will have a high-quality user interface that you can use to create all-in-one, integrated projects.
-
product
PXI 32 x SPDT Reed Relay
40-110-121
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
BGA SMT Adapters
Giga-snaP™
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, i...show more -
product
Clamshell Type Mechanical Fixtures
Series 70
The VP Series 70 Mechanical Test Kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface.
-
product
Computer On Module
ITX-M-CC452-T10
The ITX-M-CC452-T10 is an industrial Mini-ITX small form factor Type 10 reference carrier board designed to fully test WINSYSTEMS’ COMeT10-3900 COM Express Type 10 Mini module. The carrier board adheres to the PICMG COM Express specifications providing compatibility with other COM Express mini type 10 modules.
-
product
Riser
Designed to provide extra space in a SUMIT stack. They are printed circuit boards (PCBs) with SUMIT mounting holes and bus connectors.
-
product
PC System Electronics
Keysight PC electronics provide state of the art laser interferometer performance in the convenient PC backplane format. Axis, servo-axis and compensation boards are available.
-
product
SATA Solid State Drive (SSD) Modules; 2TB TLC
FM9
SATA Solid State Drive (SSD) Modules (FM9) is a plug-in SATA drive compatible for use with NAI single board computers and multifunction I/O boards where a direct SATA interface to a processor is supported. The FM9 module has a capacity of 2TB in a triple-level cell (TLC) construct.
-
product
SCR CONTROLLER WITH REGULATOR
The SCR Controller and the Regulator Board are used in SCR controlled power supplies.CEHCO offers single phase and three phase SCR Controllers with Regulator Boards.Click the links below for additional details.
-
product
CompactPCI Chassis 4 Slots
2U 84HP
Hartmann CompactPCI 2U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 4 slot 5V I/O 9U monolithic (6U cPCI) backplane for horizontal mounting of boards.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - PCIe
Model 7050
- Now available in RFSoC Gen 3 with the Model 7053- Supports Xilinx® Zynq® UltraScale+" RFSoC FPGA- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2, and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional front panel dual optical MPO interface for gigabit serial communication- Unique QuartzXM eXpress Module enables migration to other form factors- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free l...show more -
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts...show more -
product
Protocols
Excalibur Systems provides a large selection of board level products for test & simulation, as well as, the embedded environment. Choose from a number of avionic protocols under platforms such as, USB/Ethernet, PC/104, PMC, PCI, Compact PCI, VME and VXI.
-
product
Printing / Squeegee Force
CmPrint
Measurement of the Force-Time Curve while Printing. The first step into the manufacturing of electronic printed circuit boards (PCBs) is printing. The solder paste is printed on the PCB using a stencil. The equal distribution of the paste pressure is crucial and affects the overall quality of the finished circuit board. An important influencing factor is the accuracy and reproducibility of the squeegee force.
-
product
LGA 1200 Intel® Xeon® W & 10th Gen.Core™ Proprietary Server Board with 4 x DDR4, 1 x PCIeX16, 2 x PCIeX4, 5 x USB 3.2, 3 x SATA 3, Quad LANs and IPMI
ASMB-610
- Proprietary server board with LGA 1200 Intel® Xeon® W & 10th Gen. - Core™ i9/i7/i5/i3 processors- Compatible with HPC-61 series chassis- DDR4 2933/2666/2400 MHz ECC/Non-ECC UDIMM up to 128 GB- One PCIe x16 slot or two PCIe x8 slots support FH/10.5" Length Cards- Two PCIeX4 slots support low profile expansion cards- 3x SATA 3 ports and 5x USB 3.2 ports- One M.2 2280/2242 (SATA / PCIe compatible)- Quad LAN with Intel I350- Flexible IO board design
-
product
iRobot Nodes
NITOS team has made mobile nodes using "iRobot Create" with a custom designed tray to hold the system board. The board is an "Alix Board" of "PC Engines" company . Commands are sent to the robot over a serial port and the whole system is powered from the robot's battery. The upward facing camera is used to recognise specific patterns on the ceiling, which help the robot navigate around the room.
-
product
3U CompactPCI 9th Gen Intel® Xeon®/Core™ i7 Processor Blade
cPCI-3520 Series
The cPCI-3520 Series is a 3U CompactPCI blade available in single-slot (4HP), dual-slot (8HP) or triple-slot (12HP) width form factors with various daughter boards to provide a broad range of I/O requirements. Faceplate I/O in the single-slot (4HP) version includes 1x DVI-I, 2x GbE and 1x USB 3.0 port (these I/O are common to all versions). Faceplate I/O in the dual-slot (8HP) version includes additional 2x USB 2.0, 1x COM, 1x KB/MS and Line-in/Line-out on the cPCI-3520D or additional 2x Display...show more -
product
Mezzanine Cards
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
product
6U CompactPCI
Advantech offer 6U CompactPCI CPU boards, rear transition modules, peripheral boards, and support for PMC or XMC module.
