Showing results: 1291 - 1305 of 3346 items found.
-
SIS3300 -
Struck Innovative Systeme
The SIS3300 is an 8 channel 6U VME digitizer/transient recorder with a sampling rate of up to 105 MHz (for the individual channel) and 12-bit resolution. The board has a width of one VME slot (4TE). The boards multi event and dual memory bank functionality make the card the choice for many demanding digitizer applications.
-
RS-485 -
SparkFun Electronics
This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
-
Omnetics Connector Corp.
Omnetics PZN (Polarized Nano) connectors offer some of the smallest board to cable mounted connectors in the industry. Using the most rugged Nano-pin to socket systems assure high performance in low profile light weight interconnections. These ultra-miniature connectors are available in a variety of board mount options as well as wired options.
-
Dev Board (with Headers) -
SparkFun Electronics
This is the SparkFun ESP8266 Thing Dev Board --- a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
ICS Electronics
* Pre-machined, single-slot wide flat front panel.* Fits virtually any VXI B and C-size board.* Ejectors pivot on mounting brackets that mount on the PC board.* Each kit includes front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.
-
CmPrint -
CeTaQ GmbH
Measurement of the Force-Time Curve while Printing. The first step into the manufacturing of electronic printed circuit boards (PCBs) is printing. The solder paste is printed on the PCB using a stencil. The equal distribution of the paste pressure is crucial and affects the overall quality of the finished circuit board. An important influencing factor is the accuracy and reproducibility of the squeegee force.
-
Diamond Systems Corp
Diamond Systems offers software support for our embedded computer boards, ranging from drivers to complete OS board support packages. The currently available driver and BSP support can be found by clicking on the links below. If what you need is not listed, please contact us to discuss custom software support options.
-
CPCI-6713-2 IP -
ALPHI Technology Corporation
The board consists of private SDRAM and Flash memory attached to the 300 MHz, TMS320C6713B floating point DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is available for downloading programs into a nonvolatile memory. A PCIbus connector provides the interface to the host computer.
-
CAEN S.p.A.
Power Supply Systems are 100% internally developed and designed to install into a standard 19” relay rack. The mainframes and dedicated HV/LV boards were purposefully designed to provide peak performance in a broad spectrum of operational scenarios and for a vast number of detector types. CAEN mainframe systems are modular, making upgrade and maintenance a breeze.A single mainframe may house and provide control for up to 768 independent channels. Each mainframe may be configured with a mixture of both High Voltage boards for detector bias and Low Voltage boards to drive peripheral electronics.
-
Model 4802 -
ICS Electronics
ICS's GPIB to I2C Interface Board is an IEEE-488.2 GPIB and HP-IB compatible interface for I2c and SMB devices.
-
FB3001 -
TEAM SOLUTIONS, INC.
Ribbon cable between digital I/O channels on CPCI-3xxx boards & D37 connector on 3U cPCI bracket.
-
ADLINK Technology Inc.
3-4U chassis for 3U CompactPCI boards, most of which are with front/rear panel I/O and redundant power supplies.
-
ATS9872 -
AlazarTech
ATS9872 is an 8-bit waveform digitizer board that can sample two analog inputs at rates up to 1 GS/s.
-
ViTec Co. Ltd
The system is designed for visual control of the application of adhesive layers on corrugated board products before assembling them.
-
APC8620A -
Acromag, Inc.
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system.