-
product
Full-Automatic Testing Machine for Hard Board Car
U690HDIR
1. CCD automatic alignment, the alignment accuracy reaches ± 15μm2. Support layout test, displacement function3. Automatic marking function
-
product
IF Receivers, Digital Demodulators and Combiners, TM Displays
The IF Digital processing board is a workhorse for all digital demodulation and combing. It can also support other unique functions like sub-carrier demodulation, FM/FM demodulation and tone receiving. Please consult the factory for your unique requirements.
-
product
Large Photo Signal Generator
DDS9m
170MHz 4-Channel Signal Generator. The DDS9m generates four independent, phase synchronous sine wave output signals and is programmable in 0.1Hz steps from 0.1Hz to 171MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. The DDS9m is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 3.3 VDC power. SOF8_409 windows software is available as an extra cost accessory.
-
product
COTS PC/104 Carrier Cards and Boards
Sundance Multiprocessor Technology Ltd.
COTS PC/104 Carrier cards and boards
-
product
Isolated Analog Expansion Board
MSXB 085
The MSXB 085 Isolated Analog Expansion Board provides isolated analog inputs and isolated analog outputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
product
Analog Multiplexer Board
104-AIM-32 PC/104
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
product
High Speed Ethernet DAQ
Ultraview's ethernet based acquisition boards bring low noise, large channel count solutions to common open-source platforms. The flexibility of being able to combine a large number of publicly available firmware/software modules with laboratory quality data acquisition chips makes many previously difficult project integrations possible at a fraction of the cost of developing the entire system.
-
product
MIL-STD-1553 Interface Board
EXC-4000VME/MCH-x / EXC-4000VXI/MCH-x
The EXC-1553VME/MCH and EXC-1553VXI/MCH cards are based on a MIL-STD 1553 certified "Summit" chip used in many flight critical systems. Each dual redundant channel supports both MIL-STD-1553A and MIL-STD 1553B protocols. Up to eight channels may be programmed individually to operate as a Bus Controller, Remote Terminal, Bus Monitor, or Remote Terminal / Concurrent Bus Monitor. The 32 K x 16 of RAM allotted to each channel for the storage of data and control parameters may be updated in real time.
-
product
Fault ID & Repair
As a manufacturer of bare PCBs, you know that your reputation sits right on top of every board you send out. You have to get them right, but with every PCB you discard, you’re throwing away precious labor, materials, power and time, along with many other costly elements that go to make up your products. That’s why it’s important to know which of your flagged boards are in fact electrically sound, and whether repair is a viable, reliable option.
-
-
product
PCI/PDXI/ISA Boards
United Electronic Industries, Inc.
For PCI bus16 analog outputs, 16-bit resolution8 digital input lines, 8 digital output linesThree clock/interrupt lines, three 24-bit counters/timersChannel list (64 locations)Independent waveform on each channelSimultaneous channel update; update on external event2k samples onboard buffer size (upgradable to 64k samples)
-
product
Turnkey Optical Modules
Optimom
Accelerate your development and focus on your true added value with Optimom™, a new range of turnkey image sensor modules, that can be instantly integrated into vision-based systems. Optimom modules are complete board-level vision extensions which comprise of our proprietary image sensors, a compact board, standard connectors, and optional embedded lenses in various options.
-
product
JTAG Boundary-Scan Controller
NetUSB-1149.1/SE
8-TAP USB 2.0 and LAN Based JTAG Controller. The NetUSB-1149.1/SE is an advanced 8-TAP USB 2.0 and LAN-based JTAG/boundary-scan controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
Off-Set Kelvin Test Sockets
This is an innovative and robust contact technology for making Kelvin contact to 0.5mm pitch QFNs. The contact uses a tip that is angled to one side, matched to an orientation that's flat on the tip. Two such contacts placed in opposition will touch the pad within 0.125mm. And because the tip is offset, the probe diameter is a robust 0.39mm and the load board pad pitch remains 0.5mm.
-
product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
product
16 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-16-8
8 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-8 has 16 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
product
3U OpenVPX SOSA™-Aligned MFIO-Intensive Processing Board
68G6
The 68G6 is a SOSA™-Aligned 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. In addition to the standard expansion plane (EP) PCIe and control plane (CP) Ethernet control interfaces, the 68G6 facilitates convenient external access to supported NAI PCIe function modules through its 1 x1 PCIe interface, enabling seamless expansion of host SBC functions for enhanced project solutions, while also offering external access to supported NAI FMx ...show more -
product
Graphics/Video Capture Board
NVP2102
The Abaco NVP2102 is a chip-down 3U XMC graphics output and video capture board based on the NVIDIA® Pascal ™ (GP107) Quadro® P2000 GPU. The NVP2102 leverages the high performance of the GPU with its 768 CUDA cores and 4GBytes of GDDR5 memory to deliver 2.3 TeraFLOPs of peak performance with CUDA™ and OpenCL™ support.
-
product
Automatic Double-Sided Bare PCB Final Inspection AVI System
FI-18 Series
InScan Limited (SIP) Co., Ltd.
InScan FI-18 is a compact and high performance fully automatic double sided AVI system for Final Inspection of PCB boards.The setup is based on golden board and CAD data which greatly simplifies the setup process. The FI-18 series inspects and processes a double sided board sized 210X300 mm 5.5 sec. Superior interline high resolution CCD sensor.
-
product
96-Pin Micro-D Connector Block, Male DIN Rail Mounted
40-966-096-M
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
9GS/s 8 Bit, 4GS Mem 4CH 16 Markers AWG
P9084B
The Proteus P9084B, is a 9GS/s, four channel arbitrary waveform generator packaged in a 4U, 19” standalone box with a 9” touch screen and on board PC , offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P9084B offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
product
Shock Test Apparatus
SCR Elektroniks make Shock test Apparatus is used to test the Electrical accessories / appliances for their mechanical strength. A wooden base fixed to a concrete block and a wooden platform is hinged base. This platform carries a wooden board, which can be fixed at various distance from the hinge and two vertical positions. The end of board bears a metal stop plate, which rests on coiled spring having constant 25N/mm.
-
product
SparkFun Qwiic Scale
NAU7802
The SparkFun Qwiic Scale is a small breakout board for the NAU7802 that allows you to easily read load cells to accurately measure the weight of an object. By connecting the board to your microcontroller you will be able to read the changes in the resistance of a load cell and, with some calibration, you'll be able to get very accurate weight measurements. This can be handy for creating your own industrial scale, process control or simple presence detection. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Self/Fast Boot use on SKY Boards
Each of these loads occur internally to each SKYbolt board at the speed of the internal SKYbolt busses; we are not limited to the speed of the VME bus, the host VME interface or the disk. These program loads also occur in parallel so the startup time is independent of the number of SKY boards in the system.
-
product
Multi-Protocol Board
EXC-4000VME/VXI
The board supports up to 8 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family, the 1553 MCH family and the ARINC-429 RxTx. Additional modules are being added constantly.
-
product
Solid-State Inline (SIP) Four-Pin Relays
Series AS4
Series AS4 solid-state single inline (SIP) four-pin relays are designed for mounting on a printed circuit board. The relays offer built-in voltage protection and can withstand very high current overloads. The relays have a low zero-cross window. The compact size and triac output make the AS relay the perfect retrofit for electromechanical relays. All Series AS relays are Zero-Cross switching.Available options include:AS24D4E/R 4Arms, 12-275Vrms, 600Vpeak Load; 4-30Vdc ControlAS24D4E-X1 4A...show more -
product
RF Connectors
HD-EFI Connectors
The HD-EFI product series is a micro-miniature interface designed to allow large board tolerance stack ups, blind mating, and multiple RF lines. It is available in common PCB jack and cable plug configurations, with an assortment of bullet adapters to accommodate many board to board spacing options.
-
product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory ...show more -
product
224 Channel Digital I/O Modular PXI Card
GX5731
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
product
Clock And Trigger Synchronization Board With Atomic Clock
CLKSYNC-PCI-AC
CLKSYNC-PCI-AC is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI-AC is designed for use with multi-channel, ADC and DAC systems where precise clock and trigger synchronization are required.
