Showing results: 3076 - 3090 of 3346 items found.
-
CAPA13R -
Axiomtek Co., Ltd.
The CAPA13R is powered by the onboard AMD RYZEN™ Embedded V1807B/V1605B processor with Radeon™ Vega graphics. The 4K embedded board is well-suited for graphics-intensive applications such as medical imaging, video surveillance, 3D simulators, optical quality control, digital signage, kiosks/POI, thin clients, and more. The integrated AMD RadeonTM RX Vega graphics with support of DirectX 12 and OpenGL 4.5 marks the cutting edge of embedded graphics. The CAPA13R can deliver truly impressive user experiences and outstanding 3D graphics quality through two HDMI, one DisplayPort and one LVDS interfaces. Its onboard CPU is attached on the rear side of the board, which can aid with heat dissipation and offers flexibility for easy system integration and minimum maintenance. Moreover, the CAPA13R offers multiple expansion interfaces with one M.2 Key E slot for wireless modules and one M.2 key B slot for storage cards. One 260-pin SO-DIMM socket on the CAPA13R supports up to 16GB of DDR4-2400 (V1605B) and DDR4-3200 (V1807B) memory. The system has a +12V DC power input.
-
Model 71610 -
Pentek, Inc.
- 32 bits of LVDS digital I/O- One LVDS clock- One LVDS data valid- One LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAs- DMA controller moves data to and from system memory- Up to 2 GB of DDR3 SDRAM- PCI Express Interface- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- RoHS Compliant Lead-Free Version Available
-
OP-SB5GL -
LINEEYE Co., Ltd.
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
CP387 -
Wuntronic GmbH
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
VP4000 -
K-WILL Corp.
The The frame delay of 2160p full sample 4K reference video and 4K test video are compensated to fit exactly to each other by pixel base, and a real time objective quality score (DSCQS) are calculated by the ITU-T J.144-based assessing method in conjunction with the differential values (PSNR). This scheme is best suited to the encoder evaluation, online/standby comparison, inspection geared to video servers, and so on. For conventional 1080i image evaluation, a single PROBE4000 board can serve the purpose.
-
ScanExpress DFT Analyzer -
Corelis, Inc.
Test coverage statistics provide engineers and managers valuable information to make critical decisions in product development and manufacturing.ScanExpress DFT Analyzer is an automatic test coverage analysis tool for printed circuit boards and systems that include a mix of boundary-scan and non-boundary-scan devices. The tool assists design and test engineers to increase fault coverage and reduce boundary-scan test procedure development times. Using ScanExpress DFT Analyzer results in better informed test decisions.
-
LXA/128-MF -
Cytec Corp.
These Chassis control up to 16 modules with up to 8 relays per module. A large variety of different switch modules are available to build almost any configuration. Modules are available to build matrix or mux configurations or discrete relay modules. Input detection modules, output driver modules and proto board modules allow custom systems for almost any application. LEDs on the front panel show switch and power status. A thumbwheel manual control is optional.
-
Domino Series -
Euresys Inc.
The Domino series is a range of high-end PCI and PCI Express frame grabbers for analog cameras. They support any system function associated to industrial acquisition, such as camera asynchronous reset, exposure and strobe control. The latest Domino boards - Melody, Harmony and Symphony PCIe - are based on an innovative proprietary technology called D Technology*. It provides a perfect digital image with the benefits of a proven analog environment: low-cost, reliable cabling and connections, smallest cameras, low power,
-
Model 8113 -
ICS Electronics
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Panther 2K-CT -
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
MODEL LCA-9PC -
Transducer Techniques, Inc
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
MODEL LCA-RTC -
Transducer Techniques, Inc
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
xiD -
XIMEA GmbH
*Quality components - Sony "EXview HAD CCD II" sensors delivering 2.8, 6.1, 9.1 and 12 Mpix*Fastest - Highest speed using full 4 TAP readout potential*Industry standard interface - Compliant with USB 3.0 SuperSpeed specification*Versatile mini camera - Subtle 60 x 60 x 39 mm, 320 grams (1)*Power - Lowest power consumption starting at 3 Watt, bus powered with USB3 cable*Cool - Minimal heat dissipation with passive COOLing*Compatibility - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM and 30 Libraries*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Bandwidth potential - 5Gb/s interface 400Mpix/s data throughput*Software interfaces - GenICam / GenTL and highly optimized xiAPI SDK for Image Processing*High grade - Quality class of sensors is combined with specially selected IR filters *Easy deployment - Range of accessories and widest hardware and software interoperability*Highly Customizable - Available in Board level and with Peltier TE Cooling
-
IFB-10003-INP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
IFB-10003-ANP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
