-
product
PCI Analog IO Board
MS 1803
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
product
RF Connectors
Radio Frequency Coaxial Connectors Are Designed To Connect Printed Circuit Boards (PCBs) And Cables To An External Antenna, Cameras, Sensors Or Other Devices.
-
product
In-Circuit ESR & DCR capacitor Tester
236
This In-circuit ESR & DCR capacitor tester is designed to measure ESR (equivalent Series Resistance) on capacitors range from 0.47uF to 2200uF, in or out of circuit. The ability to trouble shoot in-circuit saves time and makes the 236 a must for anyone that tests or trouble shoots PCB (printed circuit boards).
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will pl...show more -
product
Test Of Aviation Turbo Starter
The use of a 16-bit analog input board provided high measurement accuracy, and the use of the SCXI reconciliation system allowed the integration of signals from the most diverse sensors in one configuration. The software developed at LabVIEW implements all kinds of tests of turbo starters in full accordance with the approved methods.
-
product
IPTV Set-of-Box Auto Test System
IPTV Set-of-Box test system is general audio/video test system for IPTV RCA signal output. This system has these features: Based on high-speed, high resolution data acquisition board from National Instruments. It can support all video and audio parameters testing. High speed, 3x than traditional video analyzer and audio analyzer Cost down. Traditional video analyzer is expensive and difficult to adopt in factory pipeline Easy-of-use software interface
-
product
General Purpose 4 Channel Optocoupler Board
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility.
-
product
Digital I/O PXI Card
GX5150
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
product
In-Circuit Fixtures
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
product
RFSoC Board
VP431
VP431, the next generation of our highly successful VP430, is a 3U VPX commercial off-the-shelf direct RF processing system that features the 3rd-generation Xilinx Radio Frequency System-On-Chip (RFSoC). The VP431 maximizes I/O channel density, reduces the radio frequency signal chain complexity, and allows for heterogeneous processing capability.
-
product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ Desktop Processor
AmITX-CF-G
Targeted at gaming customers and system integrators, AmITX-CF-G is a Mini-ITX board specially designed for Gaming. AmITX-CF-G features GLI compliance, easy and flexible configuration, security enhancements, and system resilience. The values of AmITX-CF-G include amplified visual impact, guaranteed system integrity, secure transactions with fast TTM and low TCO, and maximized system uptime. AmITX-CF-G can satisfy application function requirements and meet GLI certification which cannot be offered by other conventional Mini-ITX boards.
-
product
MCCI Catena® 4551 Integrated Node for LoRaWAN™ Technology
Based on the Murata CMWX1ZZABZ-078, and designed to be compatible with the Adafruit Feather family of development boards and accessories, the Catena 4551 is a great platform for LoRaWAN investigation and deployment. It works well with The Things Network, or any LoRaWAN 1.0 or 1.1 network in the 865 to 923 MHz range.
-
product
X-ray Inspection Of PCB Boards And More
The RTX Series
Glenbrook’s RTX Series of modular, real-time systems include models designed to meet a variety of production requirements including circuit board components. Numerous options make it easy to customize any RTX model to your specific application. All hardware and software elements are fully compatible to ensure the continued value of your equipment.
-
product
224 Channel Digital I/O Modular PXI Card
GX5731
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
product
IF Digital Processing Board for Demodulation and Combining
LS-35-R
The Lumistar LS-35-R is part of the Lumistar family of digital processing boards used for programmable telemetry systems. The LS-35-R consists of a digital processing main board with two high capacity Xilinx Virtex-5 arrays. The LS-35-R provides a two-channel IF Receiver with Pre/Post detect combining, multimode demodulators with data rates up to 40 Mbps, bit synchronizer outputs, Viterbi decoding, spectral and constellation display, BER reader display and 70 MHz IF modulator with calibratednoise feature. The all-digital design assures a consistent product with high reliability and long-term stability.
-
product
USB to TTL Adapter
SKU-012-0X
The USB to TTL adapter connects the Serial UART to the standard USB port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
product
HPx-250 PMC Radar Input Card
The HPx-250 card provides a similar set of capabilities to the HPx-200 but on the compact PMC form-factor. The PMC board may be fitted to a compact PCI (cPCI), VME or VPX host processor card for a rugged embedded solution.
-
product
Arduino Shields
Arduino shields are modular circuit boards that piggyback onto your Arduino to instill it with extra functionality.
-
product
6U cPCI Multi-function I/O Boards
78C2
NAI’s 78C2 is a 6U cPCI Multifunction I/O and Communication Board with six independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Pressure Sensors
A pressure sensor is a device that senses pressure and converts it into an electric signal where the amount depends upon the pressure applied. TE Connectivity (TE) designs and manufactures pressure sensors ranging from the sensing element to system packaging for harsh environments. We are an industry leader for our range of both standard and custom pressure sensors, from board level components to fully amplified and packaged transducers. Based on piezoresistive Micro-electromechanical systems (MEMS) and silicon strain gauge (Microfused, Krystal Bond) technology, our sensors measure everything from less than one inch of water column (<1.25 mbar) to 100K psi (7K bar).
-
product
Semiconductor Package Wind Tunnel
WT-100
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
product
4 Port RS-232 & 4 Port RS-422 Interface cPCI Card
GX3904
The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.
-
product
Board Test Adaptor (BTA)
MS 1104
BTA is used to test and validate TARANG (RWR) boards. The BTA has PC interface through RS232 / USB communication port. GUI based Test Software is used to test the UUTs and displays the result.
-
product
Multipurpose Module for SLSC
Bloomy’s Multipurpose Module for SLSC provides a convenient location in an SLSC system for applications ranging from a simple rearrangement of signals to installation of circuits and components. Both front panel connectors are mapped to screw terminals, through holes, and surface-mount technology pads thus accommodating a wide variety of components. Breakout areas for all rear transition interface (RTI) pins simplify integration into SLSC-based systems. On-board power supplies (±15VDC, +5V, and +3.3V) are also made available for the user’s analog and digital circuits. The module features a considerable amount of available board space for user applications.
-
product
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter
4044
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter. The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot. It provides a migration path for PCI-X board suppliers to port their products to a PMC-X form factor. As the PMCX equivalent board is developed, software development and migration can proceed with the original PCI-X board operating in a PMC-X environment.
-
product
ARM
Single board computer combines high performance multimedia graphics with a rich mix of industrial I/O. The Freescale i.MX 6DL processor's integrated power management provides excellent efficiency and allows operation from -40 to +85C without active cooling. It is designed for demanding graphical applications in security, transportation, medical, and digital signage.
-
product
Large Board Stencil Printer
MC1200
Manncorp's MC1200 SMT large board stencil printer fills application requirements of large-board assemblers with print areas ranging from two feet to nearly four feet in length, making them ideal for LED, backplane and multi-panel assemblies. These big-board printers, priced at one-half to as much as two-thirds less than competing large-board printers, are ideal replacements for slower and less accurate manual printers.
-
product
MPI PCB Probe Systems
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
-
product
Flat Front Panel Kits
* Pre-machined, single-slot wide flat front panel.* Fits virtually any VXI B and C-size board.* Ejectors pivot on mounting brackets that mount on the PC board.* Each kit includes front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.
-
product
Pressure To Current Measurement Trainer
Unitech Scales And Measurements Pvt. Ltd
Pressure to Current (P to I ) Trainer:This setup comprises of pressure chamber fitted on a base board. A pressure transducer and bourdon pressure gauge are fitted to the chamber. Digital pressure indicator with transmitter output is provided to display the pressure sensor by the pressure transducer. Transmitter output 4 to 20mA can be measured by a current meter. Foot air pump is provided to build the pressure.
