Showing results: 151 - 165 of 3345 items found.
-
-
MSXB 013 -
Microstar Laboratories, Inc.
Digital Expansion Boards. The MSXB 013 Digital Input/Output Expansion Board expands 16 digital input lines and 16 digital output lines to 64 digital input lines and 64 digital output lines.
-
Axiomtek Co., Ltd.
The 3.5" embedded board is created in an architecture of low power consumption with reliability required for various applications in rugged environments. The ZIO form factor is an integrated interface standard defined by Axiomtek and has been adopted as one of our specifications in our 3.5" embedded single board computers to meet concerns regarding insufficient expansion interfaces in small form factor (SFF) single board computers.
-
VME-4132 -
Abaco Systems Inc
VME-4132 32-Channel Analog Output Board with Built-in-Test
-
TIO-10 #1 -
VI Control Systems Ltd.
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channel can be used to measure frequency or period.
-
Focus-275 -
Kyoritsu Testsystem Co., Ltd.
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
VME-2128A -
Abaco Systems Inc
VME-2128A 128-bit High-Voltage Digital Output Board with Built-in-Test
-
Aldec, Inc.
HES™ is a feature-rich family of SoC/ASIC pre-silicon physical prototyping and hardware emulation boards. The family features boards with high-performance devices from either Xilinx (including Virtex-7, Virtex UltraScale, Virtex UltraScale+ and Zynq UltraScale+) or Microchip (PolarFire and SmartFusion2).
-
XJIO -
XJTAG Ltd.
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Alliance Support Partners, Inc.
An increasing number of electronics products are being assembled in panels of 8 or more to minimize production cost. These products are typically tested with in-circuit tests (ICT) followed by power-on functional tests. Normally, ICT requires isolation of power and ground while measurements are being performed. Functional tests, including in-system programming (ISP), require board power to be applied. The Modular Relay Board (MRB) is designed to switch power onto each individual board and to disconnect sensitive signals during functional test.
-
VME-3123A -
Abaco Systems Inc
16-Bit High-Throughput Analog Input Board, 16 Channels with Simultaneous Sample-and-Hold Inputs
-
BCM91125E -
Broadcom Limited
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
6602 -
VI Control Systems Ltd.
Interface board for converting signals on a National Instruments PCI/PXI 6602 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channels can be used to measure frequency or period. Digital inputs or outputs can be substituted on channels that are not needed for timing purposes.
-
SBC -
Eurotech Inc
*This section contains a wide range of Single Board Computers (SBC) available in many form factors: EPIC, EBX, and much more. *These embedded Single Board Computers come in standard form factors in compact sizes with rich I/O, high flexibility, easy expansion capabilities and extended temperature options.
-
CeTaQ GmbH
By measuring production components placed on a circuit board one can not correctly define the placement machine accuracy