-
Product
Accelerated Life Test Systems
-
Test systems for accelerated life testing and product burn-in utilize Intepro’s electronic loads that are ideal where high power bulk loading is required. Characterization applications within Telecommunication and Aerospace sectors benefit from Intepro’s environmental stress screening (ESS)/Burn-in solutions
-
Product
Metal Detector Combination System
-
The metal detection combination system is designed for simultaneously detecting metal contaminants and reducing giveaway in food products. This system is perfect for inspecting a wide variety of food products, including retail-packed convenience food/ Food to Go and much more.
-
Product
Fuorescence LED Illumination System
pE-2
-
The pE-2 is a fluorescence LED illumination system which provides repeatable and controllable light with a choice of 20 different LED peaks. It is perfect for the researcher who has a specific set of tests to conduct. The user can specify a wavelength configuration matched to their particular fluorescence requirements. It is modular, allowing LED wavelengths to be exchanged as requirements vary or additional experiments are added. Manual control is via a remote control pod with instant on/off and intensity control from 0-100%. Additionally, the system is fully integrated under many imaging software packages.
-
Product
Power System Simulator
F6150e
-
This power system simulator performs the simplest through the most complex tests. Meeting all your protective relay testing needs, the F6150e is available in different configurations.
-
Product
Temporary Bonding Systems
-
Temporary bonding is an essential process to offer mechanical support for thin or to-be-thinned wafers, important for 3D ICs, power devices and FoWLP wafers, as well as for handling fragile substrates like compound semiconductors. A device wafer is bonded to a carrier wafer with the help of an intermediate temporary bonding adhesive, allowing the typically fragile device wafer to be processed with additional mechanical support. After the critical processes, the wafer stack is debonded. EVG’s outstanding bonding know-how is reflected in its temporary bonding equipment, which has been provided by the company since 2001.
-
Product
Single Sensor Enhanced Vision Systems
-
Rely on the industry leading Max-Viz enhanced vision systems (EVS) from Astronics to enhance your safety and situational awareness while flying.
-
Product
S-parameter Measurement System
DPS21
-
Unlike a coaxial tube type or a wave guide tube type, this method does not make errors caused by air-gap as specimens are not put into a fixture. Practical data can be obtained even at the rough, uneven surfaces where the specimen is placed on.It enables compactness and measuring specimens by plane wave because of direct installment of lens with an antenna.It enables measurement by monitoring S21 and S11 parameter with connections of a test fixture to a vector network analyzer and PC.
-
Product
Dynatrol® Level Switch for Light Bulk Solids
CL-10GJ
-
Dynatrol® CL-10GJ Level Sensor is designed for sensitive or problem applications of materials that have a tendency to bridge or pack. It handles difficult products such as flour, cocoa, sugar, pharmaceutical powders, powdered lime and additional bulk solid materials for high, intermediate or low-point level detection. The CL-10GJ is typically used with bulk solid materials in the density range of 10-15 lbs/ft3.
-
Product
ECHO VS System with Image Enhancement
Echo VS
-
The ECHO VS system adds our Image Enhancement Suite to the ECHO platform to provide industry-leading image quality and defect identification capabilities. It’s our most accurate ultrasonic NDT equipment for development labs and for production environments that require the highest precision. The Echo system can be fitted with an optional chuck for manual wafer inspection.
-
Product
CT/VT Test System
-
Fully pre-wired comprehensive turn test system. *Suitable for CTs up to 6000A & VTs up to 132kV. * Precision to (0.005 class) internal multi-ratio standard CT. * Internal 4KA current source. * State-of-the-art Instrument Transformer Test Set AITTS-98 with computer & printer interfaces. * Electronic potential divider facilitates testing any VT ratio upto 132kV. * Current & potential burdens.
-
Product
Battery Conductance and Electrical System Tester
MDX-P300
-
The MDX-P300 is the first tester available from Midtronics which features an integrated printer allowing for immediate printing of test results. Now it is easier than ever to show thecurrent state of the battery and electrical system by providing customers with a printed result of the battery and system test. Using patented Conductance Technology, perform a quick, simple, and accurate battery or system test in seconds, and review the printout with the customer for added impact to preventive maintenance routines and customer service.
-
Product
Imaging Gauge Software Test System
-
The IMAGING GAUGETM quality analysis system was developed by APPLIED IMAGE to address the growing need to standardize the evaluation of camera image quality. The system includes a Test Chart manufactured using our ACCUedge® technology, along with unique Image Analysis Software, used together to analyze the quality of the imaging system, and then provide a summary report on the various image quality metrics. Our goal is to provide a simple to use, unique image analysis system, that can be utilized by R&D, scientists, system integrators, technicians and field operators to evaluate the camera quality or imaging system.
-
Product
Test System
LB303
-
Computer Gesteuerte Systeme GmbH
The test system features the durable G12 receiver from the Virginia Panel Cooperation for the adapter interface. The LB303 is equipped with a power supply of max. 6 kW and can control up to 2 load boxes (in an external rack).
-
Product
Dynamic Weighing System for Wheel Loaders
Loadtronic 3
-
Modern wheel loaders are designed for increased productivity under all conditions. It is important not to lose these properties after installing a weighing system. The Loadtronic 3 weighing system will never tell you to slow down, even on rough surfaces. It helps your company save time and money and increases your profit. This is possible because the Loadtronic 3 has the built-in dynamics system. Drive as you normally do, move fast and flexible. Load more tons per hour. Instead of giving away valuable goods, load the correct amount every time.
-
Product
512 Channel Systems
Spider-80X/Spider-80Xi
-
The Spider-80X is designed for applications in three fields: dynamic data acquisition, vibration control, and machine monitoring. Each front-end features eight analog input channels and two channels that may be software selected as analog outputs for vibration control or tachometer inputs for the analysis of rotating machinery.
-
Product
IOL & Power Cycling Test Systems
-
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
Product
Prop Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
Product
Real Car Transient Test System
RealCar Simulation Bench
-
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
Product
Acoustic Emission (AE) Monitoring System
Sensor Highway II System
-
The Sensor Highway II System™ is an Acoustic Emission (AE) monitoring system with up to 16 high-speed channels and 16 standard parametric input channels (expandable to over 100). The system is designed for unattended and remote monitoring use in Structural Health Monitoring management and condition monitoring applications. It is rated for outdoor use and comes equipped in a rugged weather proof NEMA 4 enclosure.
-
Product
Charge System Safety
-
Renesas' charging system safety circuits are optimized to provide a redundant safety protection to an Li-ion battery charging system by monitoring input voltage, battery voltage and charge current.
-
Product
Auto Charging System Analyzer
TE6-0606
-
Hangzhou Tonny Electric & Tools Co., Ltd.
This unit simply plugs into your car's cigarette lighter socket and will present you with alternator and battery status. On the left side is the alternator status indicating if it's charging the battery at too high a voltage, normal or too low. On the right is the battery status green LED charged 12.4-12.6V, yellow LED recharge 11.8-12.35V, and red LED dead<11.75V indicators.
-
Product
Basic Digital Systems
-
The Medical Imaging System can be configured simply by installing the FCR Reader, the CR Console, and the Imager to your existing X-ray equipment. The Imager uses the dry film for output and therefore does not require a dark room as in conventional systems thus saving space. Also, the scanned image can be digitally saved to media and not on films, thus not much storage space is required.
-
Product
Broadcast Control and Monitoring System
Cerebrum
-
As a complete Broadcast Control System (BCS), Cerebrum gives you control over your most critical broadcast operations. Accessible via one application, the system’s powerful and highly customizable interfaces allow you to control, configure and monitor any broadcast environment the way you want. Cerebrum is designed to be robust in both small to large infrastructures and adapted for SDI and IP, offering you a scalable solution that is ready for today’s and tomorrow’s operations.
-
Product
Modular System for Automated Quality Control
TEST-9110-VXI
-
The TEST-9110-VXI "Flight" system is a Russian modular system for automated quality control of harnesses and wiring. The system is built on the basis of the international VXI standard, and all its components are manufactured entirely in the Russian Federation by the Informtest holding. The advantages and simplicity of TEST-9110-VXI have already been appreciated by more than 50 leading Russian enterprises in various fields of production. Starting from 2007 and up to the present moment, “Polyot” is the most popular system of this class in Russia, which completely replaces similar import systems in its parameters.
-
Product
Three-Phase Test System
TESTRANO 600
-
TESTRANO 600 is the world’s first portable, three-phase test system which supports all common electrical tests on single- and three-phase power and distribution transformers for routine and diagnostic testing on-site or during factory acceptance tests (FAT).
-
Product
Mill & Silo Monitoring System
MSM-100
-
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.
-
Product
Development System
FE-51RD2
-
* Emulates Atmel AT89C51RD2, AT89C51ED2 and others * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Modular Test System
DMT
-
The DMT Tester is a modular test system that allows rapid measurement of electrical and non-electrical parameters of functional units. The system also allows basic ICT measurement with optional accessories. It is conceived as modular, with the possibility of integrating a wide range of own and external instruments. The DMT tester is controlled by its own SCADUS software.
-
Product
Measuring Systems For Beverage Can Manufacture
RICOS - Specialized Ring Contour Gauge For Drawing Dies
-
Optik Elektronik Gerätetechnik GmbH
Special designed for measurement of inside profile (land angles) of ironing dies for 2-piece beverage can manufacture, tolerance model and comparison with CAD data. Measuring task of RICOS is the measurement and evaluation of the inside profile of ironing rings in beverage can manufacture The measuring and evaluation system RICOS serve the profile measurement and the tolerance evaluation of ironing rings for beverage can manufacture.
-
Product
Class 2 Sound Level Meter
SP79
-
The SP79 is a Class 2 sound level meter for on-site measurements in accordance with Noise at Work legislation in industrial and office environments. Featuring A and C frequency weighting and fast and slow time weighting, the compact design can be handheld, or mounted on a tripod for longer term monitoring of Min / Max values. Detailed recording and analysis can be made using the AC and DC outputs. The SP79 complies with BS EN 61672-1:2003 and is supplied with a detachable windshield and hard carry case. The large high contrast display includes both digital reading and analogue bar graph. An optional Class 2 sound level calibrator is available to verify accuracy before and after readings in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB.
