OMICRON electronics
Specialization in power system testing.
- 1-800-OMICRON
1-713-830-4660 - 3550 Willowbend Blvd
Houston, TX 77054
United States of America
-
Product
Hybrid Signal Analyzer
DANEO 400
-
DANEO 400 is a hybrid measurement system that records and analyzes all conventional signals (voltages, currents, hard wired binary status signals) and messages on the communication network in a substation.
-
Product
Portable Protection Test Set and Calibrator
CMC 430
-
The CMC 430 is the preferred choice for test engineers in cases where excellent transportability is needed and three currents up to 12.5 A or six voltage outputs are sufficient. Its low weight of just 8.7 kg / 19.2 lbs, and robust design with its edge protection predisposes the device to every outdoor and indoor use.
-
Product
Protection Test Set
COMPANO 100
-
COMPANO 100 is the universal and easy-to-use solution for all types of basic testing duties in electrical energy systems. Controlled electronic sources allow the user to obtain exactly the desired value and to output signals with variable frequencies and other signal forms, automated ramps, and pure DC.
-
Product
Three-Phase Test System
TESTRANO 600
-
TESTRANO 600 is the world’s first portable, three-phase test system which supports all common electrical tests on single- and three-phase power and distribution transformers for routine and diagnostic testing on-site or during factory acceptance tests (FAT).
-
Product
Relay Test Set and Universal Calibrator
CMC 256plus
-
The CMC 256plus is the first choice for applications requiring very high accuracy. This unit is not only an excellent test set for protection devices of all kinds but also a universal calibrator.
-
Product
Current Transformer Analyzer
CT Analyzer
-
Current transformer testing in a multifunctional instrument performing excitation, ratio, polarity and winding resistance tests on current transformers as well as burden impedance measurement.
-
Product
Companion for on-Site Testing
PTMate
-
The PTMate app is our mobile companion for the Primary Test Manager™ (PTM) software. It supports you on site by providing additional features on your smartphone, for example, sending images, displaying wiring diagrams, or sharing jobs and reports.
-
Product
Handheld Grounding Tester
HGT1
-
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
Product
Mobile, Hardened Test Set
MBX1
-
With the MBX1 platform and our software, you can easily test SCADA and substation automation systems (SAS) in a highly secure way. The mobile solution allows you to perform quick assessments and temporary monitoring, e.g. during commissioning.
-
Product
Sweep Frequency Response Analyzer
FRANEO 800
-
FRANEO 800 was developed for testing the mechanical and electrical integrity of power transformers after transportation or exposure to high fault currents. It uses the sweep frequency response analysis (SFRA) principle and measures the electrical transfer function over a wide range of frequencies.
-
Product
Programming Interface for CMC Test Sets
CMEngine
-
CMEngine is an open programming interface that enables you to integrate the CMC test sets into your own testing environment and control them within any type of application.
-
Product
12 kV Insulation Fluid Test Cell
CP TC12
-
The CP TC12 oil test cell is for determining the relative permittivity, the dissipation factor and the power factor of insulating liquids such as transformer oil.
-
-
Product
Dielectric Insulation Analyzer
DIRANA
-
DIRANA uses dielectric frequency response (DFR) analysis in order to determine the condition of high-voltage insulation systems such as those in power transformers, bushings, cables and generators.
-
Product
Three-Phase Relay Test Set
CMC 353
-
With its compact design and low weight of 13.3 kg / 29.3 lbs, the CMC 353 provides the perfect combination of portability and power. It is the ideal test set for three-phase protection testing and the commissioning of SCADA systems. The powerful current outputs (3 x 32 A / 430 VA) optimally support 5 A relay testing.
