Inverter Test
-
Product
VLSI Test System
3380D
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
-
Product
6TL10 Table Top Test Base
H71001000
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Semiconductor Test System
TS-960e
Test System
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
Test Module
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
Test Handler
M4841
Test Handler
High-Throughput Device Handler for Volume Production Testing of MCUs and DSPs.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
Memory Test System
T5511
Test System
Offering Multi-functionality and Industry's Top Test Speed of 8Gbps.
-
Product
6TL24 Combinational Base Test Platform
H71002400
Test Platform
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
Electronic Control Unit Functional Test
Functional Test
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
TestStand
test
TestStand is industry-standard test management software that helps test and validation engineers build and deploy automated test systems faster. TestStand includes a ready-to-run test sequence engine that supports multiple test code languages, flexible result reporting, and parallel/multithreaded test.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Bluetooth RF Test System
FRVS
Test System
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
Product
LitePoint RF Test System
J750
Test System
The option of adding LitePoint instrumentation to the J750 system delivers a cost-effective, complete production test solution covering global wireless connectivity standards.
-
Product
Test System
UltraFLEX
Test System
The UltraFLEX test system delivers the power and precision you need for complex SoC devices built for mobile applications, networking, storage or high-end processing. Choose UltraFLEX when your device mix and throughput goals demand the highest speed, precision, coverage and site count.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
Test Fixture
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
SoC Test System
V93000 SoC / Smart Scale
Test System
Advantest’s V93000 Smart Scale generation incorporates innovative per-pin testing capabilities. Each pin runs it own sequencer program for maximum flexibility and performance, for example in multisite applications. Full test processor control ensures time synchronization between all card types, like digital, Power, RF, mixed signal and so on. The user benefits are reduced test time, best repeatability and simplified program creation. The system design makes it easy to extend your configuration with new modules and instrumentation, as your test needs change.
-
Product
Compact EMS/EMI Test Platform
CEMS100
Test Platform
Setting up an EMS/EMI test system is a very complex process requiring significant investment. The steps involved include custom planning, design, installation and configuration of various components and standalone instruments as well as the RF shielded anechoic chamber. Rohde & Schwarz offers the standardized R&S®CEMS100 test platform that is the company's first flexible, reliable and cost-effective off-the-shelf solution for radiated EMS measurements in line with IEC/EN 61000-4-3.
-
Product
SoC Test Systems
Test System
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
-
Product
Radar Test System
UTP 5065
Test System
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
Product
PCB Test System
Circuit Wizard - CW409
Test System
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
Product
PXI Digital Test Instrument
PXIe-6943
Test Instrument
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.This instrument is TPS-compatible with the legacy VXI digital test instrument from Astronics as well as other instrument vendors.
-
Product
Fixturing Kit
10744A
Test Fixture
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
Test System
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
EBIRST 50-pin D-type To 2x8-pin Power D-type Adapter
93-005-236
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
