Showing results: 1336 - 1350 of 2647 items found.
-
DR-700 -
Daerim Electronics Co.
1. Insulation resistance measurement(earth-state, line-cut, line-short, and telephone capacity measuring) 2. Tone & pulse dialing3. Speakerphone for hands free two way conversation4. Subscriber calling5. Last number redial6. Hook and flash function7. High impedance monitor function8. Transmitter mute switch9. Continuous polarity LED indications10. Line powered with high voltage protection11. Water-proof
-
MI series -
Ono Sokki
There are MI-1271, 1/2-inch back electrets-type microphone which has improved the environmental stability against temperature and humidity, MI-1235 which emphasizes on a wide frequency range and MI-1433 which realizes a similar environmental resistance at a low price. MI series microphone is used in combination with the preamplifier and the microphone. Since microphone and preamplifier are not built-in type, installation costs can be reduced in the event of a fault.
-
ASM-BF/2 | VP 230044 -
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/2 4WD roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-BF/2 4WD is built into the base.
-
Acopian Technical Company
These modular High Voltage supplies may be used as constant voltage or constant current sources. They may be remotely programmed by means of either voltage or resistance, and have provisions for remote monitoring and output inhibiting. All control and monitoring connections are on a pluggable terminal block that functions as a connector, providing wiring convenience and permitting easy and rapid connect/disconnect. Outputs are arc/short circuit protected.
-
TM530 -
T&M Tools Limited Co
TM530 Audio Frequency Generator is provided with Pinpoint Fault Locator for pinpointing the low resistance fault and detecting cable route. When detecting, TM530 will inject a signal current of 1kHz audio frequency into the cable, and accordingly a magnetic wave of the corresponding frequency will be generated on the cable. Pinpoint Fault Locator will collect this magnetic signal, thus obtains the information of the cable fault and the route.
-
TF140C -
TESTEX Testing Equipment Systems Ltd.
It enables rapid determination of the dynamic resistance of materials designed to be subjected to strong shearing loads (e.g. fabrics) or liable to be damaged by sharp or heavy objects (e.g. paper bags). Subsequently, the test was naturally adopted for all materials in the form of sheet or films, cardboards, cloth, knitted fabrics, plastic films, aluminium foil, non-woven fabrics, complex flexible packaging etc.
-
CT8017 -
General Technologies Corp.
State of the Art ergonomic design and styling for easier handling and use. Full Auto Ranging range selection. Manual range selection function. Large 3 digit LCD display with analog bar graph. AC/DC Voltage measurement up to 600 Volt. Manual or automatic VDC/VAC selection. DC Current measurement up to 10 A. Resistance measurement up to 32 MOhm
-
HH2205F -
Colluck Company Limited
High Accuracy (Basic Accuracy 0.5%). 3-3/4 Jumbo LCD display 4000 count with symbolic signs. Auto Ranging High Voltage test up to 1000V DC and 750V TRMS AC. Higher Current test up to 20A AC/DC. Diode and Continuity check. Measure Resistance up to 40MΩ. Measure Temperature up to 760oC or 1400oF
-
Sensirion AG
The microthermal gas meter modules from Sensirion enable gas consumption to be reliably monitored in real-time. The modules boast long-term stability and dust and dirt resistance and have proven their mettle in the field for several years. In Germany and Italy, over 100''000 sensors have been integrated in microthermal gas meters. The advantages of the gas meter module make it the epitome of smart energy.
-
National Technical Systems
Will your products, subsystems or components operate as designed when exposed to fire conditions, or will they go up in flames? Fire and flammability testing is required for products used in a wide range of industries, including Aerospace, Defense, Telecommunications, and Consumer Electronics. NTS offers fire and flammability testing services, typically falling into two categories: 1) ignition and flame spread, and 2) fire resistance.
-
PCR4T -
RARA Electronics Corporation
Precision cement resistors designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow high precision measurements even with low resistance values. PCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a ceramic molding. This resistor has low inductance and has high pulse power.
-
GBR-181 -
RARA Electronics Corporation
GBR-181series resistors are made in a thick film technology, or ceramic substrates (Al2O3) - 96&). Thick film resistors are characterized by a higher stability, and lower noises than a typical carbon resistors. The whole of resistor is encapsulated with epoxy resin by fluidization process. GBR-181 series elements are used both for general, and professional applications. Other values of resistance, and tolerance (up to 0.1%) are available on request.
-
Kobold Instruments, Inc.
Diaphragm pressure gauges feature stainless steel construction for superior chemical and corrosion resistance for your intermediate pressure measurement applications. Because of the protective diaphragm seal design, these pressure gauges are ideal for use with viscous as well as corrosive fluids. Optionally, these diaphragm pressure gauges may be ordered with glycerine filling to help dampen the effects of machine vibration and pulsation of the media.
-
Sataton Instruments Technology CO., Ltd
Rubbing fastness tester/Crockmeter is professional designed for determining the resistance of the color of textiles of all kinds, including textile floor coverings and other pile fabrics, to rubbing off and staining other materials in dry or wet conditions. Rubbing fastness tester can also be used to determine the color fastness to rubbing of ink, printing, dyeing, etc. There are two modes of manual and automatic for different requirements.
-
Part Number: -
TESTEX Testing Equipment Systems Ltd.
Horizontal Flammability Tester, to determine the comparative burn rates and burn resistance of textiles, particularly those for automotive interior use. Horizontal flammability tester is safe and easy to operate, Comprises draft free stainless steel cabinet with observation window, sample holder and door mounted burner. Horizontal Flammability Tester complies with ISO 3795, ASTM D5132,FMVSS 302, etc.