Showing results: 1516 - 1530 of 2653 items found.
-
KHZ43201 -
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
KT7193 -
Ketai instrument (kunshan) Ltd.
● 3 3/4 digits 3999 count● Extra high DC/AC current measurement● Data hold to capture measurements● Backlit display is easy to read under any light condition● AC current measurement up to 1500A● DC current measurement up to 1500A● DC/AC voltage, resistance, capacitance, frequency and temperature measurement● Diode and continuity test● Accessories included: 9V battery, carrying case, test leads, K typetemperature probe, English manual, gift box
-
KT7201 -
Ketai instrument (kunshan) Ltd.
● 3 1/2 digits 1999 count● 20 range in 6 functions● Backlight display is easy to read under any light condition● Low battery indication● Overload protection● DC/AC voltage measurement up to 500V● DC current measurement up to 10A● Resistance measurement up to 2MΩ● Fuse: F200mA/250V, F10A/250V● Transistor polarity tests● Accessories included: 9V battery, elastomer boot, test leads, English manual, gift box or blister card
-
ASM-P-PLUS | VP 230047 -
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
ASM-P | VP 230046 -
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
Fieldpiece Instruments, Inc
A classic style multimeter with True RMS and phase rotation. This manual ranger covers the electrical parameters you need for HVACR and, with detachable test leads, works with our accessory heads to test non-electrical parameters too. The LT16A meter measures current, resistance, voltage, capacitance, frequency, continuity and more. Test leads store in the meter body along with the tilt stand and magnetic hanger. The body is constructed of durable ABS plastic and a blue backlight makes the large LCD even more visible.
-
PCE Instruments
The cable length meters of PCE instruments provide various functions that can be useful in terms of measuring the length of cables or detecting cable breaks. Therefore the cable length meters function according to various measuring principles that will be described below. Using these devices enables determining cable lengths as well as the resistance and caliber of cables that are about to be laid or even already laid. Depending on the device that is being used, you can measure the length of cables to certain extends. Also the measuring ranges differ among the the devices.
-
National Technical Systems
Dielectric Constant is used to determine the ability of an insulator to store electrical energy. The dielectric constant is the ratio of the capacitance induced by two metallic plates with an insulator between them to the capacitance of the same plates with air or a vacuum between them. Dissipation factor is defined as the reciprocal of the ratio between the insulating materials capacitive reactance to its resistance at a specified frequency. It measures the inefficiency of an insulating material. If a material were to be used for strictly insulating purposes, it would be better to have a lower dielectric constant.
-
SA10A -
Elcon International AB
It has a built-in micro Ohm meter/Ductor for measuring of static and dynamic resistance of the breaker poles. It only weighs 11,6 kg. The versatility and precision that this unit offers is, without question unchallenged, and it will indeed be your best partner when testing circuit breakers. Tests in areas with high induction at known problematic substations has proven the SA10A to be the only circuit breaker timer that could withstand these extreme conditions. It's rugged, it's small and highly appreciated by our customers.
-
Customized X500 -
beltronic IPC AG
The customized X500-MIL notebook unit is based on the X500 unit designed by the manufacturer GETAC for Industrial or Military environments requiring a reliable and robust system. It achieves certification levels military MIL-STD-810G (in terms of resistance to mechanical and thermal environments) and MIL-STD-461G (in terms of compliance with EMC standards) and it can even be certified TEMPEST SDIP- 27 level A, B or C.The customized X500-MIL unit can also be powered directly by an on-board voltage between 12 to 36 VDC while respecting the MIL-STD-1275 standard.
-
Premier Electrosystems
Premier Electrosystem's Insulation Resistance test (also known as Megger, Mega Ohm Meter, Million Mega Ohm Meter) indicates whether any corrective maintenance or replacement of installed equipment is necessary, to assess if the newly installed equipment can be safely energized, and to trend the gradual deterioration of the equipment over its service life. Insulation Resistance Test is carried out to ensure the healthiness of overall insulation system of electrical equipment. It reflects the presence or absence of harmful contamination, dirt, moisture and gross degradation. Common areas of application are testing of appliances, wires, transformers, harnesses, motors, etc.
-
NX Hipot+ -
Dynalab Test Systems, Inc.
* 50 to 1500VDC Hipot Testing * 50 to 1000VAC (optional) * Expandable to 1024 test points * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
BA8100 -
B&K Precision Corporation
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
eBIRST -
Pickering Interfaces Ltd.
The eBIRST toolset consists of three different tools that support 200-pin LFH, 78-pin and 50-pin connectors and a set of adaptors that allow connection to other connector types. A supplied application program controls the eBIRST tools via a USB2 port that also provides the tool power and controls the switching system using a Test Definition File to define the test sequence. These tools work by measuring the path resistance at the switching system external connectors using four-wire measurements, quickly establishing whether the path is good, has increased resistance or has failed. Below are links to various eBIRST tool information:
-
XD71 -
Hangzhou Xihu Electronic Institute
The device is used for power transformer power outage routine test items to do automated testing.Which is characterized by dielectric loss, insulation resistance, DC resistance, tap-changer switching characteristics, short circuit impedance and variable ratio of six test items are concentrated in an instrument,so that the instrument function, test power and test lead height fusion.Field test, just start wiring once, at the end of unplugging wiring once,the middle process by the test personnel in the computer terminal to send command control,the test system automatically completes all or part of the above test items.
