Showing results: 1996 - 2010 of 2653 items found.
-
2108 EL -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Four functions : DC current, AC current, AC+DC current, and ACV measurement.● Three input resistance ranges: 1kΩ,1.5kΩ and 2kΩ.● 200uA full scale value.● ±2.5% full scale value accuracy.● Built-in overload protection circuit.● Robust, compact and easy to carry.
-
MCL-400IR+ -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
Teledyne LeCroy
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
ACMAS Technologies Pvt. Ltd.
Xenon is one of the noble gases and is a major component of arc lamps and flash lamp and it also has its importance in general anesthetics. One of the major applications of xenon lamp is that it can be used in research applications to simulate the sunlight.Weiber walk in xenon lamp chamber uses xenon lamp to simulate the whole sunlight spectrum that can produce many destructive effects on the products. This simulation environment provided in the chamber is used to test the resistance of various manufactured products towards these destructive conditions. This chamber is used for quality control, product development and scientific researches and many more. With a variety of models and options, you can customize your chamber to fit your testing needs. With walk in option you have a facility to test your product in bulk quantity and even for the products which are larger in size. This chamber also known as Uv Test Chamber and Xenon Lamp Weather Resistance Test Chamber.
-
DMT-4010RMS -
Monacor International GmbH & Co. KG
*True RMS measurement method*Dust and water protection according to IP class 67 with covered measuring sockets*Auto ranging for faster measurements*4000 digit resolution*Additional bar display*Voltage measurement up to DC/˜ 1000 V*Current measurement up to DC/˜ 10 A*Frequency measurement up to 10 MHz*Resistance measurement up to 40 MΩ*Capacitance measurement up to 40 mF*Temperature measurement -20 °C to +760 °C*Acoustic continuity test*diode test*Data hold (measured value memory)*peak hold*Maximum and minimum value recording*LC display with switchable background lighting*Automatic shutdown*overload protection*Supplied with test leads and protective case
-
ENVIROMUX-FENCE1 -
Network Technologies Inc
Detects when individuals climb over or cut through chain link or wire mesh fences. Advanced built-in signal processor prevents false alarms. Four sensitivity settings to tune each sensor to a particular fence section and intrusion type. Two open-collector outputs – alarm and power failure. UV resistant case and epoxy sealed electronics provides maximum resistance to harsh environments. Rated NEMA 4X and UL94 5V. Use individually or chain units with each ranging from 40 to 60 feet away. Includes mounting brackets for installing the sensor to fence fabric. Screw terminals. Operating temperature: -4 to 131°F (-20 to 55°C). Operating voltage: 9-15V DC.
-
CM55 -
Martindale Electric Co. Ltd
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
Part No. InP1012-20 -
Teledyne Defense Electronics Relays & Coax Switch
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-20GHz
-
Part No. InP1012-14 -
Teledyne Defense Electronics Relays & Coax Switch
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-14GHz
-
Part No. InP1012-30 -
Teledyne Defense Electronics Relays & Coax Switch
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-30GHz
-
DCM401 -
Draper Tools Ltd
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
40-523-021 -
Pickering Interfaces Ltd.
A 44x4 medium density matrix - product range comes with available reedrelay formats of 1-pole, 2-pole and 1-pole screened. The screened version is suitablefor switching signals up to 50MHz. These PXI matrix cards are constructed using highreliability ruthenium electro-plated reed relays, offering >10e8 operations togive maximum switching confidence with long life and stable contact resistance.
-
93-005-202A -
Pickering Interfaces Ltd.
The 93-005-202A 50-pin D-type to 23xSMB Coaxial Adapter is part of our range of eBIRST USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Vibration Shock -
ZETLAB Company
Software Vibration shock is used for testing specimen resistance to vibration impact. This software is a part of the software complex ZETLAB VIBRO, supplied together with vibration control systems ZET 017-U. The software enables generation of impacts with pre-set parameters and noise presence within a specified frequency range. The software is activated via ZETLAB control panel and VCS menu.
-
igentic® 621t -
Sterner Automation Limited
Growing demand for light emitting diode (LED) products and increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. The igentic® 621t is a flexible PCB tester that ensures quality while increasing production. The tester can handle multiple PCB products and test for light measurements, resistance and push button or post detection, as required.
