Showing results: 3106 - 3120 of 5224 items found.
-
GX96404-60 -
Marvin Test Solutions, Inc.
Mating Coax Connector with 20 Coax Pins crimped (one end) to 5' wires. Coaxial cable: RG316, 50 ohms.
-
N9910X -
Keysight Technologies
N9910X Rugged phase-stable cable, 3.5 mm(m) to 3.5 mm(f), 26.5 GHz, 3.28 ft or 1 m
-
Qualitrol
Partial Discharge Monitors provide a complete package that includes sensors, cables, data acquisition unit, processing unit (CPU) and software.
-
Advantech Co. Ltd.
Advantech is your source for industrial wireless accessories including WiFi antennas, adapters, cables, Ethernet radios, mounting brackets and more.
-
Teledyne Marine Impulse-PDM
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
410104273 -
Virginia Panel Corporation
This G6 ITA is equipped with a removable EMI-shielded backshell. This backshell slides up to provide access to wires and connectors. This ITA also includes a keying feature. Removable and adjustable U-shaped cable clamps are attached by screws to the ITA frame and allow ITA modules to be pre-wired before assembly. The clamps can hold cable bundles with an oblong bushing effective diameter of 1.59". ITA strain relief plates are not needed.
-
250 SSP -
Aines Manufacturing Corp.
This probe is designed for those technicians that want the best tool available. The Model 250SSP is supplied with a cone-shaped tip and a duckbill tip that is longer and flatter, permitting insertion into larger cables, or cables under tension where slack cannot be obtained. Another feature is the built in speaker for audio without the need for a butt set or headset. The speaker is operated by a slide switch that has a "lock" position for continuous monitoring.
-
PD-TaD 60 -
BAUR Prüf- und Messtechnik GmbH
The PD TaD 60 portable PD Diagnostics system is used in combination with a BAUR VLF generator frida for carrying out partial discharge measurement and location.* Comprehensive 360° cable analysis – with parallel partial discharge and dissipation factor measurement* Time-optimised and safe cable condition evaluation* The lightest and most compact PD measuring device up to 60 kVpeak* Developed for portable use on site
-
40-967-160-F -
Pickering Interfaces Ltd.
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.
-
40-967-160-M -
Pickering Interfaces Ltd.
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.
-
92-965-025-M -
Pickering Interfaces Ltd.
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Extech MA3110 -
Extech Instruments Corporation
Flexible 11" (28cm) clamp jaw easily wraps around bus bars and cable bundles that may be difficult to access with regular clamp meters. The thin 8mm cable diameter easily fits into tight spaces. Includes test leads for multimeter functions measuring Voltage, Resistance, and Capacitance. True RMS and CAT IV rated allows for maximum accuracy and safety for your measurements.
-
DCSS502BC -
Sanshine Electronis Co., Ltd.
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
N1410A -
Keysight Technologies
The N1410A is a starter kit for B2985B and B2987B Electrometer/High Resistance Meter and includes N1414A High resistance measurement universal adapter and N1415A Triax to alligator cable. The N1414A helps you setup the cables and makes the cabling setup easier. The N1415A is recommended to measure more than 1 nA current, but you can probably measure less than 1 nA current with appropriately shielding.
-
Megger Group Ltd.
Locating high and low impedance faults on paired metallic cables is a crucial yet often difficult task for a telecoms engineer. Megger designs TDRs specifically for the communications industry, which makes each unit a safe, application specific tester that can be used on virtually all communications cable types. The wide range of TDRs makes it easy to choose the tester with the resolution and range you need.