Showing results: 2536 - 2550 of 5224 items found.
-
Abaco Systems Inc
A 6”cable transitions from the card edge connector on the RAF-EC-2P (champ 36) to one male HD-15 connector and two shielded RJ-45 connectors.
-
510109339 -
Virginia Panel Corporation
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Pin Female SCSI Connector
-
186380-0R5 -
NI
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 0.5m
-
186380-02 -
NI
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 2m
-
-
192190-01 -
NI
RJ50 10-pin Modular Plug to DB-9 (Male), 1m
-
-
Cable Nooks -
ALTINEX, Inc.
Designed for boardrooms and conference rooms, the modular Cable-Nook provides a simple and effective way of hiding/storing multimedia cables and connectors. The cables remain connected to a presentation system enabling the user to access connections to video, audio, and other media sources. The modular Cable-Nook uses a half-moon lid that remains flush with the table when not in use. To access the cables or connectors, simply lift the door and pull the cable ends out, or plug computer video cables into any installed fixed connectors. The lid closes easily even with several cables in use. After the presentation, the cable ends are returned to the Cable-Nook for safe storage.
-
Weshine Electric Manufacturing Co., Ltd
Cable harness tester is used for test and measure wire cable harness,wire harness, like as : auto cable, audio cable, power cable, network cable, telephone cable, USD cable, HDMI cable,video cable, etc. .
-
System Software 3 -
BAUR Prüf- und Messtechnik GmbH
The BAUR system software is a cable testing, cable diagnostics and cable fault location package. It enables efficient monitoring of the condition of cable networks in combination with BAUR cable fault location, testing and diagnostics systems.
-
LKZ-720 -
Sonel S.A.
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
System Software 4 -
BAUR Prüf- und Messtechnik GmbH
The BAUR system software is a cable fault location, cable testing and cable diagnostics package. It enables efficient maintenance of cable networks in combination with BAUR titron systems.
-
72-6706 -
Tenma
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
TDR 500 -
BAUR Prüf- und Messtechnik GmbH
Handheld Time Domain Reflectometer. The handheld time domain reflectometer TDR 500 and TDR 510 are used for fault location in all metal cables such as power cables, coaxial cables, data cables and communication cables.* Configurable for various measurement ranges and cable types* Standard-compliant, safe measurements on life cables through the measurement category CAT IV / 600 V (with separation filter)* Ideal for fault location in the area of telecommunication, video technology, data and security technology
-
PCE Instruments
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.