Showing results: 4156 - 4170 of 5224 items found.
-
Extech 401014 -
Extech Instruments Corporation
401014 is a Big Digit Thermometer that simultaneously displays indoor and outdoor temperatures. Its waterproof sensor for outdoor measurement extends on a 9.6 ft. thin cable for easy installation. Internal memory stores Min/Max readings over time. Thermometer comes complete with built-in stand, external temperature sensor, AAA battery, and wall mount bracket.
-
Extech TL620 -
Extech Instruments Corporation
The Extech TL620 is a 200 MHz, 10:1 Oscilloscope Probe with a 1.2 meter cable. It features a 10 M ohm input impedance, 20 pF Capacitance, max voltage of 600 V, and 15 pF to 40 pF compensation range. Includes probe tip, ground lead, marker ring, sprung hook, and adjustment tool.
-
Extech 380562 -
Extech Instruments Corporation
Compact and precise, the Extech 380562 Milliohm Meter has 7 ranges and measures down to 0.01mΩ using 4-wire Kelvin clip test leads. Measurements are displayed on the unit's large 0.8", 1999-count LCD. Built-in comparator for Hi/Lo/Go resistance testing or selection. Complete with 4-wire cables with Kelvin clip connectors and power cord.
-
GPIB -
Test Electronics
Test Electronics will customize the TE3000 GPIB signal routing box for your test application. Then, you simply rack and stack all the equipment, cable all the switched signals to the back of this GPIB box, add a rack mount computer, plug in the National Instruments GPIB board and software. Then run your customized GPIB based test system.
-
F9 Systems, Inc.
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Omron Industrial Automation
Save panel space and simplify design of external I/O blocks for PLCs and other controllers with plug-in relays. PLC interface adapters and pre-terminated cables reduce installation time and labor connecting to Omron and Siemens PLC I/O modules, and to network interfacing slice I/O systems. The relay is the perfect choice for panel builders and industrial controls designers.
-
360 DSP -
Trilithic Inc.
The 360 DSP is a next generation fulfillment meter specifically tailored for installation and troubleshooting. The 360 DSP is part of a system consisting of the meter, ViewPoint software, and means for acquiring information from the Cable System's Workforce Management application.Upstream Return Spectrum Analysis (4 to 110 MHz). Level Mode. C/N Measurement. QAM mode (MER/BER/Constellation).
-
SBL SERIES -
Transducer Techniques, Inc
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
JT 2135 -
JTAG Technologies Inc.
The JT 2135 allows TAP signals to be extended away from the base JT 2137 (classic pod) by up to 1 meter and retain full pod’s frequency specifications. The active circuitry inside the JT 2135 compensates for the TDO signal return time of the longer interface cable. Multiple JT 2135s can be implemented if a longer extension is required.
-
Teledyne Defense Electronics
Gain Shape Linearizer Amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run, or perhaps changing the input gain response to an MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
777101-01 -
NI
50-Pin Male IDA to 50-Pin, Female Screw Terminal, Panel Mount Terminal Block - The CB-50LP provides 50 screw terminals for connection to I/O signals from 50-pin NI data acquisition devices. The CB-50LP includes one 50-pin header for direct connection to 50-pin cables and metal standoffs for use on a desktop or for mounting on a custom panel.
-
E1708A -
Keysight Technologies
The Keysight E1708A uses an optical fiber to transport the laser beam from a remote sensor assembly to the electronics. This improves measurement accuracy and repeatability by enabling you to mount heat-producing electronics away from the measurement area. The fiber optic cable also provides increased mounting design flexibility and easier access to the receiver attenuation and squelch adjustments.
-
10780C -
Keysight Technologies
The Keysight 10780C is a highly-sensitive, lowest-cost Keysight receiver used with laser interferometer positioning systems. One receiver is used per measurement axis (including wavelength tracker). Configured with Keysight electronics, laser heads, cables and optics, the Keysight 10780C receiver allows you tailor a precise positioning system for your exact application requirements.
-
85532B -
Keysight Technologies
CalPods provide a new and unique way to quickly and easily refresh a network analyzer calibration, at the push of a button, and without removing the DUT or re-connecting standards. Very useful in thermal-vacuum chamber testing, where it is desired to remove the thermal effects of the test cables and connectors from the DUT’s response, and where it is impractical to stop the testing to perform a normal re-calibration.
-
779501-01 -
NI
MXI-Express Interface, PXI Remote Control Module—The PXI‑8360 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8360 through a copper, x1 MXI‑Express cable.