Showing results: 1426 - 1440 of 9089 items found.
-
Prior Scientific Inc.
Below are two examples automated microscopy solutions, tailored towards physiology or neuroscience applications. Many of our components can be used to automate your microscope.
-
Prior Scientific Inc.
Below you can see two industrial microscope systems which can be created using our components. Many other automated microscopy systems are possible using our components.
-
Prior Scientific Inc.
Below you can see examples of two systems using our robotic sample loading system. Many other automated microscopy systems are possible using our components.
-
Rigaku Corp.
In a move to bring lab-quality performance to the manufacturing floor, Rigaku introduces the MiniFlex XpC, a manufacturing-optimized powder diffractometer for fast and accurate quality control measurements. It is extremely easy to operate using Rigaku’s new EasyX quality control software, which requires minimal clicks to run. A minimal interface means there will be no accidental error variance from operator to operator. The MiniFlex XpC can be configured with a conveyor belt or robot for automated sample processing and collaboration with other instruments. With an 800 W X-ray source and a short-diameter goniometer, the system has the performance of a lab unit, and thus can greatly improve throughput for quality control measurements.
-
2900 -
Thunder Scientific, Corp.
The Model 2900 Humidity Generation System is a self-contained system capable of producing atmospheres of known humidity using the fundamental "two-pressure" principle. This system is capable of continuously supplying relative humidity, dew point, frost point, parts per million, or other calculated values for instrument calibration and evaluation as well as for precision environmental testing.
-
PC-114 -
Com-Power Corporation
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
TS9982 -
Rohde & Schwarz GmbH & Co. KG
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
SPA Series -
Com-Power Corporation
The SPA-series high performance, low cost, easy to use, portable spectrum analyzers are ideal for a pre-compliance laboratory. All three models feature a wide frequency range and low noise floor to increase system sensitivity and system to noise ratio. An advanced, easy to use interface makes your work simple by putting the features you need at your fingertips.
-
3920 -
Thunder Scientific, Corp.
The Model 3920 Low Humidity Generation System is a self-contained system capable of producing atmospheres of known humidity using the fundamental "two-pressure" principle. This system is capable of continuously supplying frost point, dew point, parts per million, relative humidity and other calculated values for instrument calibration and evaluation as well as for precision environmental testing.
-
-
Phoenix Aerial Systems
The HydroRANGER is an evolution of mapping technology. This Airborne Topo-Bathymetric (ATB) system provides dual purpose topographic and bathymetric measurements for full scene mapping of shoreline systems. Utilizing a visible green spectrum laser with an elliptical scan pattern and measurement rates up to 200 kHz, the HydroRANGER provides a combination of high spatial resolution and spatial accuracy.
-
Avery Design Systems
Level up and perform full System HW-SW verification at pre-silicon levelIterate HW and SW changes 10X faster at RTL compared to FPGA or system prototypesBegin HW-SW integration much sooner in development processVirtual machine to VIP co-sim/co-emulate environment extends existing SV/UVM testbench + VIPsX86 HostSupports PCIe/CXL root complex VIPRun Linux kernel drivers, compliance and benchmarking programs, and application softwareArm, RISC-V embedded systemsSupports AMBA (AXI/AHB/APB) VIPRun bare metal code or RTOS embedded systemsRun OS and SW unmodified from actual system configurationDebug trace shows QEMU to remote PCIe/CXL/AXI ports transactionsAvery's implementation of QEMU co-simulation is optimized for fastest performance including KVM mode and iWARP technologySimulations are scalable to 10s to 100s of instances for regression over OS versions and HW configurations
-
Phoenix Aerial Systems
The RECON-XT is the ultimate value, entry-level system for the DJI Matrice 300. A strong fit for smaller scan areas and teams on a budget. The RECON-XT is designed to grow and adapt with your business.
-
HFDF -
National RF, Inc
National RF's Type HFDF active directional antenna system consists of a high gain RF amplifier coupled to a tunable Faraday shielded loop antenna. Several loop antenna assemblies are available to provide coverage of frequencies in the HF and low VHF spectrum. Due to the nature of a Faraday shielded loop, the antenna exhibits a sharp null through the diametric center of the loop. This null is used to determine the direction of incoming radio signals or to locate electrical noise being radiated from some source. The internal high gain amplifier is used to compensate for the inherent inefficiency of the actual loop at the operating frequency. Overall, the system dynamic response is about +6 dB as compared to the dynamic response of a dipole. To aid in the direction finding process on strong signals, an internal 30 DB attenuator is provided. As the loop antenna presents a bi-directional response, tri-angulation may be required to eliminate the ambiguous signal direction. The line of site of the incoming signal is determined by listening for a signal null on the receiver or by watching the receiver’s S-meter.
-
PVS AR -
ARC Technology Solutions
Connected to our standard, open PVS (Process Verification System) platform, the new early adopter PVS AR system, allows users to do several things, not yet seen in the industry. First, by connecting to a wide variety of standard torque tools, standard PVS connectivity allows customer choice to pick the right tool for the right job, but now allows these tools to be used in an augmented reality framework.
