Showing results: 2416 - 2430 of 9089 items found.
-
-
Terotest Systems Ltd.
Flying probe testers work by In-circuit testing the board via a number of moving test probes. They have the advantage over traditional In-circuit testers of not requiring a dedicated "bed of nails" test fixture thus reducing the price for each different board being tested. However, modern Flying Prober testers offer so much more than just In-circuit testing. They enable the user to combine In-circuit, AOI, Functional, Device Programming and Boundary Scan testing, in one test system.
-
Photo Emission Tech., Inc.
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Quest Engineering Solutions
ISTA is an organization focused on the specific concerns of transport packaging and whose mission is to develop and deliver standards, educational programs and tools for the economic, social, and environmental optimization of packaging systems. ISTA testing is a well defined shipping testing procedure designed to verify that your packaging is sufficient to protect your product during all shipping environments.
-
DEFECTOVISION IR Product Family -
Foerster Instruments, Incorporated
The DEFECTOVISION IR system is an addition to FOERSTER's core competence, the non-destructive testing of semi-finished metal products. All around the world, more than 6.5 million tons of steel have been tested safely and efficiently by now with our latest technology.
-
L-3 Cincinnati Electronics
High Intensity Radiated Fields (HIRF) testing simulates high RF peak pulsed and average fields typical of radar environments and is integral to the certification of flight essential avionics systems. L3 Cincinnati Electronics (L3 CE) can perform HIRF testing from 400 MHz to 18 GHz (with traditional average field testing from 10 kHz to 40 GHz).
-
CAST Navigation
CAST Navigation’s GNSS simulation systems produce GNSS RF signals that provide a precise and repeatable testing signal, perfect for use either in the field or in the laboratory environment. These systems can be used for a wide range of testing and integration verification applications and they are an ideal choice for stimulating military or commercial devices where only GNSS signals are needed. Our simulators are powered by proprietary multi-frequency, multi-constellation GNSS RF signal generation technology. This technology provides you with highly accurate and fully programmable signals along with advanced vehicle trajectory capabilities allowing you to custom tailor parameters and trajectories to meet your simulation requirements.
-
SFT 3316 -
Hangzhou Softel Optic Co., Ltd.
SFT 3316 IP Mux-Scrambling modulator is the latest generational Mux-scrambling-modulating all-in-one device developed by Softel. It has 1 6 multiplexing channels, 16 scrambling channels and 16 QAM (DVB-C) modulating channels, and supports maximum 1024 IP input through the GE port and 16 non-adjacent carriers (50MHz~960MHz) output through the RF output interface. The device is also characterized with high integrated level, high performance and low cost. This is very adaptable to newly generation CATV broadcasting system.
-
OLT-G8 -
Hangzhou Softel Optic Co., Ltd.
ent can be realized, including ONT function parameter set, T-CONT business lines and amount, Qos parameters, configuration information request, performance statistics, auto-reporting of running events in system, configuration for ONT from OLT, fault diagnosis and management of performance and safety.
-
SFT3508F -
Hangzhou Softel Optic Co., Ltd.
SOFTEL SFT3508F IPTV Gateway is a device which is used for the protocol conversion scenarios and streaming media distribution scenarios. It can convert the broadcast network IP stream over HTTP, UDP, RTP, RTSP and HLS and TS file into HTTP, UDP, HLS and RTMP protocol. The system can achieve the integration by receiving a variety of commercial streaming media services. Also, the system can provide streaming media services directly.
-
-
Flameguard P5-200 -
Teledyne Marine ODI
The FlameGuard™ P5-200 is a key enabling technology for a 5 kV - 200 A, three-phase dry mate electrical feedthrough system. Designed for offshore topside oil and gas platforms, where explosive and flammable conditions are likely, the feedthrough system is used to provide an electrical connection to downhole pumping systems. The feedthrough system is designed for dry tree operators and ESP pump manufacturers who want to reduce operating expenses over the life of the field, while improving system reliability and reducing safety risks.
-
ISRA Vision AG
Unlock the potential hidden in your production data and optimize both, productivity and quality.Our software solutions generate meaningful results from the data collected by your inspection, measurement, and production systems.ISRA’s solutions accompany the entire quality circle in your production. They record deviations in the process and visualize the results in real time, so that corrective measures can be taken as quickly as possible. Where predefined limits are exceeded, the system proactively alerts the relevant users. Automated reports provide maximum transparency and help users to make fast objective decisions.
-
ISRA Vision AG
Ensure consistently high quality when applying adhesives and sealants with fully automated, 100% optical in-process monitoring of all beads.ISRA’s robust sensor systems have proven their worth in challenging industrial applications and cover the full range of quality parameters: presence, consistency, bead width and height, and position relative to the component edge.
-
ISRA Vision AG
Ensure that components function and can be fitted correctly with efficient form monitoring. ISRA’s 3D form measurement systems capture component geometries down to the nanometer level while ensuring the shortest cycle times.
