Showing results: 4711 - 4725 of 5324 items found.
-
40-570-111 -
Pickering Interfaces Ltd.
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
40-570-214 -
Pickering Interfaces Ltd.
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Furaxa, Inc.
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
COMBGEN6DIFF -
Ultraview Corporation
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
TA-334001 -
Tech-Aid Products
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
CZ20250 -
Aegis Pty. Ltd.
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, and is a great Cat 5, Cat 6 and Cat 7 cable tester, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! And it tests for all these at lightning speed, saving you as much time as possible.
-
ZDP -
ZOLIX
Model:ZDP Pneumatic Vibration Isolation Optical TableDetails&Spec:Specification :Resonant Frequency: ＜1.5~2.5HzSelf-balance, short response time,high speed balanceSilence free oil compressor , presurre : 3-7kgf/cm2Pneumatic support: two payer, three import valves,4 or 6 gasbagTable structure : three layerTable top : thickness: 4-6mm,1Cr17 Ferromagnetic stainless steelBottom of table : 4-6mm,Carbon Steel;Surface spray treatment of melaninSide : internal: Carbon plateExternal:Black aluminum plateCorners: stainless steelTotal height ( table and support): 800mm, range of adjustment : -10-----+10mm Pitch :25mmx25mm;Screw :M6Weight : Thickness 100mm: 120kg/m2Thickness 200mm: 140kg/m2Thickness 300mm: 167kg/m2
-
PCE Instruments
Penetrometers measure the firmness or hardness of fruit. Penetrometers are ideal for determining the best time to harvest fruit or to test its progress to maturity. The firmness of fruit is one of the most widely used parameters in testing its maturity, together with measuring the fruits sugar content using refractometers. Electronic penetrometers come with different diameter penetration points. This allows for fruit of different size and hardness to be tested. It is important that this first part of the measurement process is done correctly if the readings obtained are to be valid in making adequate decisions as to when the fruit should be harvested. It is important the the samples that are measured are representative of the entire crop, considering a sufficient minimum quantity sample, size and quality.
-
Huntron
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design. Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
-
GAO Tek Inc.
GAOTek’s laser distance meters are used to measure the distance between the target and the device. Our device sends a pulse of laser light to the target and measures the time it takes for the reflection to return. Its ergonomic design emphasizes function and user-friendly usage. GAOTek’s laser distance meters are reliable, of high quality, and affordable instruments that provide an accurate measuring. Our products offer an easier inspection or testing experience, is compact, and portable. A laser distance meter offers efficient testing, accuracy, versatility, safety, functionality, and convenience compared to the old-fashioned tape method when used in the field. Our laser distance meters are available for purchase to the United States, Canada and globally.
-
TR-61850 -
Ametek Power Instruments
Whether a new or existing installation, AMETEK’s TR61850 adds the capability to easily monitor and record GOOSE messages within the substation. All data from the fault recorders and TR61850 automatically merge providing a single point of reference when analyzing transient events and system disturbances. With a wide range of time synchronization, communication options and small form factor, the TR61850 seamlessly integrates into any application.Configuration of the GOOSE Message subscriptions is quick and easy with AMETEK’s configuration tool. Using the IEC61850 Substation Configuration Language (SCL), third party IED Capability Description (ICD) files are imported and subscriptions are created by simply dragging and dropping available GOOSE message outputs.
-
Laminator - Three Chambers -
Qinhuangdao Boostsolar Photovoltaic Equipment Co., Ltd
1. Effective lamination area : 2400mm × 4500mm2. Dimensions: see outline drawing3. Heating method: heat conduction oil heating (63KW heating station)4. Compressed air source pressure : 0.6 ~ 0.8MPa5. Working vacuum degree: 100 ~ 40Pa6. Evacuation rate: (according to vacuum pump)7. Temperature control accuracy: ±1.5°C8. Temperature control range: room temperature - 180°C9. Temperature uniformity: effective lamination area ≤ ± 2 ℃10. Lamination cavity height: 30mm11. Evacuation time: depending on the process, it is recommended to take 5 to 8 minutes12. Upper cover stroke: 300mm13. Cooling power: 20KW
-
Lt-C/M2020B -
Teledyne Lumenera
With this next evolution for Teledyne Lumenera, the Lt Series Board Level Cameras have ports located on the side of the camera for easy access. With the Lt-C/M2020B’s 3.2 megapixel resolution, capturing clear images is simple with frame rates up to 55 fps. Instead of connecting to the back of the camera which would generally mean a longer amount of space required within a design, having connectors on the side allows for the back of these cameras to lie flush against the other components of the device. For example, vision systems in unmanned aerial vehicles (UAVs) can reduce their size and subsequent weight using Lt Series Board Level Cameras, thereby increasing flight time.
-
BOLT-Tester -
Nitto Construction Inc.
BTS(BOLT-Tester) is developed in 2012 after the collapse at SASAGO Tunnel on the Chuo Expressway in Japan. Visual inspection and hammer sound testing are main inspection methods for maintenance and management of anchor bolts in a tunnel. However, these methods have some issues in regard to objectivity and reliability of the results. Pull out testing is also one of a testing method for the soundness test of anchor bolts, however, this method have also some issues in regard to cost and time, and there is a risk to damage the anchor bolt. BTS is simple and cost effective non-destructive testing equipment that solves those issues. BTS measures a waveform of impact force to evaluate the soundness of anchor bolt.
-
OAKTON Instruments
The new addition to the Environmental Express Oakton product line features updates to measuring water quality easier and faster. The larger LCD display is 2.75 in. by 2.0 in. for a better viewing angle, and has indicators for battery life, stability, and calibration. The ION 100 meter measures pH, mV, ion concentration of 16 commonly measured ions, and temperature. The microprocessor-based meter features automatic calibration, automatic temperature compensation, function setup, self-diagnostics, automatic power-off, and low voltage display. The meter uses advanced digital processing technology, intelligently improving the response time and accuracy of your measurements. Easily switch units among pX, mol/L, and mg/L (ppm).
