Time
is an illusion of duration.
See Also: Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Counter / Timers, Atomic Clocks, Phase
-
product
Power Meter
EPM 6000
EPM 6000 is the industry's highest performance revenue grade panel meter. Based on the latest technology and an all new platform, EPM 6000 has a superior cost to performance ratio and significantly outperforms other metering products many times its price.
-
product
Multichannel Analyzers
Multichannel Analyzers (MCAs) are workhorse instruments in many scientific measurements. An MCA analyzes a stream of voltage pulses and sorts them into a histogram, or “spectrum” of number of events, versus pulse-height, which may often relate to energy or time of arrival. The stored spectrum may then be displayed and analyzed.
-
product
10 Gb/s Programmable Digital Delay Line
PDDL10
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
product
PXI/PXIe Solid State Attenuator, Hex, 6GHz, 50Ω, SMA
43-182B-006
The 41-182B-006 (PXI) and 43-182B-006 (PXIe) are programmable RF attenuator modules with 6 channels in 2 slots capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuator uses solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
product
Shoe Heat Insulation Tester
UI-FT08
Shoe Heat Insulation Tester – Thermal Insulation Tester is used to test shoe heat insulation / thermal insulation against hot performance. Place the shoe in sandbath and the footwear shall contact with the plate(forepart and the heel) in certain temperature for a given period. Then to measure the temperature increase inside of the shoe. The contact temperature and time is specified in production standard.
-
product
High Performance Power Analyzer
AFM-8A
AFM-8A has Developed for AFC*(Auto Frequency Control) high performance measurement and frequency update, its update up quickeer than 100mSec. multifunction power analyzer provides high-accuracy measurement and is designed for single phase and three phase application. It includes 4 Digital inputs, 4 Relay outputs, and a RS-485 Modbus RTU Communication port. The user can choose one more communication port, and 2 Analog outputs for output expansion.It provides measure voltage and current of the 2~63 harmonic, and it shows CO2 emissions, which is suitable for power monitoring, management and analyze power quality. It has TOU (time-of-use) function and 4MB Flash memory capacity, allowing users to record data for a long time. It also has a software line adjustment function to reduce the on-site line adjustment work.It has the functions of waveform capture and recording, power record, and event record, which can be used for multifunction power analyzer.
-
product
Multibeam Echosounder - Shallow Water
SeaBat T20-P
The ultimate combination of portability and performance. With the SeaBat Portable Sonar Processor mobilization time is reduced to help you focus on getting the job done. Fully adaptable to a wide range of applications the T20-P uses compact low-weight transducers in a 1°x1° configuration. The Portable Sonar Processor is water resistant and is capable of time tagging typical support sensors.
-
product
Cable Continuity Tester, RS232, DB9 In Line Signal, Network, 21.01 mm, 35 mm, 45.01 mm
72-9265
The 72-9265 is an In-Line Signal Link Tester. Quickly test DB9 connections with this handy tester. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini link tester fits easily in your pocket or tool box and requires no external power. Connects in-line and displays signal data connectivity on LED's per each conductor. Save time and money by diagnosing connectivity issues.
-
product
Mini-Photohelic Differential Pressure Switch/Gage
MP
The Series MP Mini-Photohelic differential pressure switch/gage combines the time proven Minihelic II differential pressure gage with two SPDT switching setpoints. The Mini-Photohelic switch/gage is designed to measure and control positive, negative, or differential pressures consisting of non-combustible and non-corrosive gases.
-
product
Emulator
Is an advanced on-chip debugging emulator and flash programmer developed with the concept of greater efficiency in development. The combination of its high-speed downloading and various software and hardware solutions will contribute to reducing development times.
-
product
PMC Card
P-DIS
The P-DIS PMC card is different from most currently available data acquisition boards. It provides multiple I/O types on a single module and the functionality to work with high-speed digital I/O signaling. With very accurate time stamping of input data and synchronization to an external IRIG-B source, the P-DIS provides the capability to precisely synchronize all output ports.
-
product
3207a GPS/GNS Frequency and Time Reference
GlobalTyme2
Precise Time and Frequency, Inc.
The ptf 3207A GlobalTyme2 GNS Receiver introduces a new level of advanced capability from a second generation, based on the highly successful ptf 3203A and ptf 3204A GlobalTyme receivers.The unit is both a frequency standard and a time standard and has been used as a precision frequency reference with low phase noise, in satellite communications applications around the world.
-
product
PCI to PMC Adapter / Carrier
PCIBPMCx2
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
product
FD-11614, 16-Channel Temperature Input Device for FieldDAQ
785854-01
The FD-11614 measures up to 16 thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11614 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11614 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11614 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
product
Synchronous GPS Based I/O Controller & Interrupter
interX
interX was originally developed as a measurement instrument for industrial and trunk pipeline anodic or cathodic protection systems. interX allows facilitate measurement of galvanic parameters (instant-off polarized potentials, pipe-to-soil potential) across a wide range of timing cycles. It is used to make synchronous disconnect and reconnect of protection electrodes (anode or cathode) or rectifier's from/to buried underground pipeline to perform measurements.
-
product
Entry-level Price Interferometer for Geometry Measurement of Single Fibers
3D SCOPE-V2
Specifically designed for use in a production environment, 3D Scope-V2 is a robust, compact and easy to use interferometer that brings speed and precision to operators. 3D Scope-V2 supports our Blink software platform. Non-compressed, real time and high quality images are transfered from the hardware to the software via a USB 2.0 link in addition to the automation and control commands.
-
product
IO-Link Transceivers
IO-Link is a Factory Automation fieldbus-independent communication standard dedicated to connecting sensors and actuators as described in the IEC 61131-9 standard. Easily integrated with any of the most commonly used communication protocols found in factory automation systems through dedicated interfaces or bridges, it is a simple solution for extending existing networks to connect remote sensors and actuators. Developers will take full advantage of the Industry 4.0 or Industrial Internet of Things (IIoT) concept where every sensor and associated data point is used to control and optimize even the most complex industrial processes in real time.
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
Salt Spray Testing/Cabinet Based Corrosion Testing
Sometimes referred to salt mist, salt fog, humidity or corrosion testingAll corrosion and environmental related tests can be tailored to customer requirementsTypical exposure times range from 16 hours to over 1000 hoursAccelerated corrosion testing can be used to check protective coatings, surface finishes and material compatibilitiesOur facilities provide a continuous controlled corrosive exposure and can combine salt spray and humidity environments.
-
product
Universal Tensile Testing Machines
Dongguan Amade Instruments Technology Co., Ltd
Universal tensile testing machines are testing equipment that are used to conduct mechanical testings of static load, tensile, compression, bending, shearing, tearing, stripping, applied to plastic sheets, pipes, tapes, rubbers, electric wires, springs, sponges, fibers etc. Tensile test is performed to measure and analyze the physical performances of different types of materials and finial products, playing an important role in developing new materials and controlling products quality. From the perspective of function, universal tensile testing(UTM) machine is an omnipotent instrument Just as the name implies. Clamps or fixtures are interchangeable on the basis of different test pieces, enabling various testings to be carried out on one tensile testing instrument. Options of single-column stand or twin-column stand can be available based on the specimen’s tensile/compressive force and dimension. Computerized tensile tester is preferred rather than microprocessor version If users want testing results including curve graphics between time, force and displacement.
-
product
Pulse Function Arbitrary Noise Generator
81160A
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
-
product
Radar Water Level Gauge
HR7310
HighReach Measuring & Controlling System Co.,Ltd
The this Series of Products's IS A Liquid Level Detection Instrument a using Microwave Technology. It IS the Designed to Monitor Natural Water or Auxiliary Water treatment the Operations and the Provide Accurate Water Level Information for Monitoring or Operating Units. At The Product absorbs at The 24GHz Planar microstrip Radar Technology of InnoSent, The signal processing adopts its own patented method, which can work solutions around the clock, and the measurement result is accurate and reliable. At the same time, the advantages of non-contact detection, strong anti-interference and low power consumption make It is even more versatile and can be used in complex water environments with contaminants or sediments such as rivers, lakes, reservoirs or sewage treatments.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
product
SIM Filter
The CFL SIMF, Cable Fault Secondary Impulse Filter from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately.
-
product
Fully Automatic Transformer Oil Test Set
OTS-A series
The Motwane Manufacturing Company
OTS-A series is fully automatic microprocessor based transformer oil test set designed with advanced features to measure breakdown voltage of insulation oil accurately. The OTS-A Series preprogrammed with worldwide acceptable standards.The user can define customized standards. The large LCD display with menbrane key pad for easy operation. It is provided with internal memory for 100 data storage & built-in thermal printer for onsite report. The kit is protected by automatic detection of poor input ground.The acrylic oil test vessel provided with adjustable electrode gap setting. The voltage calibrator for on site calibration saves cost & time of user.
-
product
Cable Length Meters
Reflect a pulse.through the cable measuring length (time domain reflectometry).
-
product
PXI Digital Reconfigurable I/O Module
PXI Digital Reconfigurable I/O Modules feature a user-programmable FPGA for onboard processing and flexible I/O operation. You can completely control the synchronization and timing of all signals and operations along with custom onboard decision making. The PXI Digital Reconfigurable I/O Module is suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom communications protocols, bit error rate testing, and other applications requiring precise timing and control.
-
product
Sodium Ion Concentration Pocket Water Meter
LAQUAtwin Salt-22
The only pocket meter that directly measures sodium ion concentration in 0.3ml sample (or 0.05ml sample with sampling sheet B) and converts it into salinity or NaCl salt concentration. No need for a beaker to calibrate the meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
product
Automatic Single Yarn Strength Tester
TY400C
TESTEX Testing Equipment Systems Ltd.
Automatic Single Yarn Strength Tester, to determine the breaking strength and elongation rate of single yarns made of cotton, wool and others up to 6000cN, with air-driven clamps. Fully automatic, can test 20 cops at the same time.
-
product
Static Design Verification
ALINT-PRO
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
