Tech-Aid Products
Tech-Aid Products is a company which is dedicated to providing quality Avionics And Instrument shop test equipment to the aviation community.
- (918) 838-8711
- (918) 835-2282
- Kim@techaidproducts.com
- 2708 N Sheridan Rd
Tulsa, Ok 74115
United States of America
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Gyro Simulator for Aircraft or Bench Use
TA-256A
-
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
Product
Dual Channel Servo Amp
Servo Amp
-
This is our Dual Channel Servo Amp board that the instrument shop can use for testing HSI's like the 331A-( ) series and others or RMI's. This board is standard in our model TA-1000 HSI tester.
-
Product
Digital Panel mounted OBI Display
TA903-01
-
This panel mounted or portable display can read the radio bus digital OBI format (Clk, Sync, Data Format) that typically drives RMI's. This format is even more widely employed with the advent of GPS/FMS and newer digital radios. This display will confirm the digital bearing accuracy of these radios.
-
Product
KMD540 Series and RDR2000/2100 Panel
TA-3C
-
The TA-3C test fixture is a combination of the KMD540 testing requirements and the RDR-2000/2100 weather radar interface requirements. This panel allows the technician to test the KMD540 MFD as a stand alone item (with external simulators) or together with a radar sensor for a dynamic real time test. The panel includes the required switching for sensor alignment and KMD testing along with input jacks for the required data inputs. Also built into the fixture is an analog gyro simulator for checking the stabilization functions of the sensor. The full enclosure comes in standard panel width.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
Dual Nav/Comm Test Panel
TA-155
-
The Best Dual Nav/Comm Test Panel on the market today. This panel is designed to test the KX155/155A and KX165/165A radios specifically as well as others and will allow by the book testing of these units. The panel includes specific switching for testing the intercom features, providing unit configuration and audio isolation as required. This panel also incudes basic provisions to run a second Nav/Comm using the long time standard 8 pin octal connector. Monitoring of either current or voltage to either radio is also provided. Integrated or stand alone testing of your OBS or converter indicators is provided as well as the required test jacks. Click on picture for larger view.
-
Product
Emergency Battery Test Fixture
TA-60
-
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
Product
Channeling Decoder, Nav/Comm/Control Head
RCD200
-
Designed to provide the Avionics shop a simple and expeditious method for testing general aviation radio tuning. Provided are front panel mounted LED's as well as a digital display to provide the quickest code recognition while testing. With this simple method of testing you will soon find yourself testing all your radios and finding those troublesome intermittents. This unit also decodes altitude and ARC 1000 serial data. Click on picture for larger view.
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
Product
Gyro Test Panel
TA-256
-
Designed to test the KI256 / KI258 panel mounted Flight Director gyros. The panel contains a power supply, the special manufacturers recommended rate board required by SA-103 to properly verify outputs As well as all other electronics required to support by the book testing.
-
Product
GAMA ARINC 429 Emulator
TA-429
-
ARINC 429 EMULATOR FOR GENERAL AVIATION (4th QTR) Unit will allow viewing multiple labels while receiving as well as when transmitting. Auto-increment when transmitting allows for more dynamic testing of equipment. All presented on a bright 4 line x 20 VFD.
-
Product
Customer Acceptance Test Panel
TA-65
-
DGS-65 Customer Acceptance Panel for both testing and trouble- shooting. We have added an option to the panel that allows you to select an analog slaving meter or the LED monitor lights as shown in the maintenance manual Fig. 5-14. The addition of the meter provides the technician with a more visible means to monitor the slaving "trend". The 50 pin DG connector is broken out on the panel to assist in monitoring or isolating unit signals.
-
Product
Universal ARINC HSI Test System
TA-1000
-
This is our ARINC Standard Universal HSI Tester designed to provide a full range of capabilities that allow testing most any HSI you will see come through your shop.
-
Product
Bi-Polar low voltage power supply board
LVPS
-
This is our standard power supply board used in many of our testers but also available separately. This board is capable of +/-15v, +10 and +5v outputs. Also contained on board is our standard meter drive circuitry for testing instrument meters, a two-pole relay and an option for a sine/cosine oscillator circuit.
