Showing results: 2866 - 2880 of 5324 items found.
-
HIOKI E.E. Corp
IP67 protected top in the industry Test all ground types from Class A to Class D with a single meter Wide 0 to 2000 measurement range Minimize cabling time with innovative earthing rods and cable winder
-
Schwarzbeck Mess Elektronik
Biconical Antennas have dipole like characteristics (e.g. circular directional pattern in the H-plane,"8"-shaped in the E-plane, fixed phase center, comparable gain), with an enormous wide bandwidth achieved by the double cone elements. One of the earliest and worldwide most popular biconical antenna designs is the BBA 9106 with balun VHA 9103 B. During the last years a growing need for expanded frequency ranges arised, which led to the design of biconical antennas reaching down to frequencies of 20 MHz and up to 18 GHz and above. A further increase of bandwidth was achieved with qualified 4:1 baluns, providing a typical gain increase of approx. 6 dB at the lower frequency range. The biconical elements can be mounted and dismounted within a few seconds providing perfect contact repeatability thanks to special clamping fixtures. A small wrench made of insulating material is supplied with the balun, it is tied to the balun head and thus always available whenever needed. Biconical antennas can be used for many applications, in which half-wave dipoles have been used traditionally. An enormous reduction of measurement time can be achieved, because the time consuming tuning of the antenna elements to the half wavelength is not needed, an important condition for sweeped broadband measurements. In typical dipole applications several discrete frequencies are measured, in contrast the biconical antenna allows continuous sweeps, where site anomalies are discovered much easier.
-
UXI-1553 -
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
780683-02 -
NI
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
780683-01 -
NI
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
781720-01 -
NI
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), Up to 12 GB/s PXI Chassis - The PXIe‑1086 incorporates hot-swappable, redundant AC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086 monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
Analog Devices Inc.
Analog Devices clock ICs and timing solutions enable new architectures, lower development and manufacturing costs, and shorter design times. Products feature low jitter and phase noise for clock cleanup, synchronization, generation, delay, and distribution.
-
WDI-2000 -
HenergySolar
The Sapphire 3D Microscope: HS-WDI-2000 was designed with high quality lighting parts and a good optical system design,can get a very clear image.with the digital camera,it can provide the image in time, widely used in LED,Solar,SEMI…
-
Pulse Research Lab, Inc.
Laying out a custom PCB is too time consuming and costly for most rush projects. Pulse Research Lab has developed Mini Modular Instruments ™ to provide cost effective solutions to the most common engineering challenges.
-
GP Solar GmbH
Innovative process- and quality control solutions (automated optical inspection – AOI) can guarantee production monitoring with very short processing time and highest quality standards. We deliver vision inspection hardware as well as software and system integration.
-
Reef -
Del Mar Photonics, Inc.
The autocorrelation technique is the most common method used to determine laser pulse width characteristics on a femtosecond time scale . Del Mar Photonics autocorrelators have been specifically designed to measure the width of pulses from femtosecond lasers.
-
AXC760x -
VX Instruments GmbH
Generate extremely short, fully regulated current pulses from 100 µs up to 100 A. At the same time, carry out measurements directly on the DUT with the integrated VMU and CMU. Perfect for rapid semiconductor tests during production.
-
928 Series -
Leco Corp.
By incorporating state-of-the-art hardware and an on-board touch-screen software platform, the 928 Series allows you to easily handle the most demanding sample applications. The core capabilities and performance of previous generations of LECO macro combustion instruments have been maintained, while key improvements have been made in throughput, uptime, and reliability. Macro sample mass ability (up to 3 grams for Nitrogen/Protein model regardless of sample carbon content) with rapid cycle times and a resulting low cost-per-analysis make the 928 Series ideal for analysis of characteristically heterogeneous, difficult to prepare, or low analyte level samples.
-
Burst Electronics, Inc
Overlays Text on VideoFront Panel Programmable or via RS232 Computer LinkUp to 32 MCG-2 on one RS232 busGenlocks to either NTSC and PAL automaticallyCharacter/Background Brightness AdjustableFour Character Heights and Four Character WidthsA-Z, 0-9 and Punctuation Marks Character SetBuilt in Menus, Help Screens and Self-testReal Time Clock (RTC) optionRemote Control via RS232 (RJ11 Connector)BNC Video Connectors, 4 Pin MiniDIN on S-VideoTen Pages of Text Storage in MemoryLithium Battery Backup (10 Year Life)Can be powered from external 12Vdc, for Field useCompact Size in a Rugged Aluminum and Steel EnclosureTwo Year Warranty, Made in USA
-
LE-270AR -
LINEEYE Co., Ltd.
LE-270AR is an Analyzer and Communication Data Logger of CAN/LIN. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on the PC. You can measure 2 channels of CAN/LIN communication lines and can simultaneously register voltage data of 4 external signals.Its power failure protection, waterproof, and low power consumption widens the usage of analyzer such as in the automation factories and other production factories.
