Showing results: 6106 - 6120 of 7502 items found.
-
34650 -
S & G Tool Aid Corp
Gives fast, accurate power steering analysis. Test for defects in power steering pumps, gears and lines. Large heavy duty gage reads from 0-2,000 PSI and 0-140 BAR. Use to rule out power steering problems before expensive suspension or steering linkage problem is attacked. Includes 13 adapters. Supplied with instructions in a durable, plastic molded storage case.
-
PS-228 -
CoolMax Technology Inc.
The product designs with LCD to show ATX power voltage. Easy to plug with ATX power 20/24 pin and plug in (P4/P6/P8) to show the voltage on the LCD panel.
-
H730008xS -
6TL Engineering
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
YAVAR438 -
6TL Engineering
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
SMX-2002 (Power) -
AMETEK VTI Instruments
The SMX-2002 is the only switch module in its class with the ability to switch up to 16A. Some applications include: AC line power switching, switching of DC or AC power supplies, control or driving relays for industrial machines (robotics, numerical control machines), automotive engine control, and solenoid switching. Since this module typically switches power to the UUT or interface, the SMX-2002 includes failsafe pins on the front panel which can be configured to open all relays when a failsafe signal is activated. This approach can instantly removes all power to the UUT or interface.
-
RP7942A -
Keysight Technologies
The Keysight RP7942A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Macken Instruments, Inc
Laser power measurements should be quick and easy. They should not involve time consuming set-up and alignment problems. Ideally, the measurements should also be able to be made at any point in an optical system where losses are likely to occur. Unfortunately, most laser power meters have sacrificed ease of use to gain continuous power readings. However, in most laboratory and production situations, the usual requirement is for a quick spot-check of power with a minimum of disruption. Even when tuning up a laser, researchers have found that it is best to tune for a desirable mode pattern.
-
Macken Instruments, Inc
The Macken Instruments, Inc., Digital Laser Power Probe is a completely portable, easy-to-use calorimeter type power meter. The instrument consists of two components: a microprocessor-based digital meter and a probe head.
-
Macken Instruments, Inc
Conical Head Power Probes are used to measure high power density CO2 laser beams which may damage the standard flat surfaced Power Probes. The conical absorbing cavity exhibits a high heat dissipation.
-
9103 -
RBD Instruments, Inc.
Rugged, portable, affordable, and ASCII programmable, RBD's 9103 USB Picoammeter (ピコアンメータ) measures dual-polarity DC current from picoamps to milliamps. It can be biased with an optional built-in fixed +90V DC bias, or your own low-noise DC power supply.
-
Panda Microwave Limited
Panda Microwave design, manufacture, and support a wide variety of Power Amplifier. RF amplifiers product line from Panda Microwave consists of low noise amplifiers, Power Amplifier Module and Solid State High Power Amplifier. Our Power amplifiers cover frequency range from 100MHz to 50GHz and used Thin-film Technology. Our low noise amplifiers have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifiers system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
Menlo Microsystems, Inc
Replace your large, slow, unreliable EM relays with the Ideal Switch. Enable a new era of connected and better protected buildings (residential, commercial, hospitals, airports), transportation (eMobility, Rail, Marine), factories (Robots and Systems), and power distribution (solar, wind, grid, battery).
-
Keysight Technologies
Keysight’s power meters and power sensors measure the power of RF and microwave signals accurately with sensors of various types (CW, average, and peak and average), covering numerous frequencies and power ranges. We offer a wide selection of power meters and power sensors for nearly all application needs — wireless communications, radar pulse measurements, component test, and more. Applications include testing the output power of communication base-station transmitters, radar system equipment, wireless devices, and much more.
-
Keysight Technologies
On a bench or in a system, Keysight variable DC power supplies are ready for your application, offering optimal voltage, current, capability and performance choices.
-
CSM Products, Inc.
The HV Breakout Modules (BM) are specifically designed for safely measuring directly from HV voltage power cables. Currents and voltages are measured directly and the raw data is acquired at up to 2 MHz per channel. With the Vector eMobilityAnalyzer software, which is optimally paired to the CSM HV Breakout Modules, real time power analysis is also possible.