Showing results: 2086 - 2100 of 7502 items found.
-
2215 -
Empower RF Systems, Inc.
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Fairview Microwave Inc.
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
AMP4065LC-2 -
Exodus Advanced Communications
Designed for EMI/RFI, lab, and general communication applications. Exodus Broadband SSPA product feature GaN, GaAsFET discrete and Chip & Wire Hybrid technologies covering one octave through decades frequency ranges from Operating Frequency Range 18.0-26.5 GHz.
-
SSPA series -
Comtech PST Corp.
The SSPA series of amplifiers operate in S-Band with power levels up to 300 watts peak. These Class 'C' amplifiers are designed for maximum power output and maximum AC to RF efficiency with minimal size. Typically used as driver amplifiers for Klystron PA's within a Linear Accelerator.
-
Nanowave Technologies Inc.
SSPAs based on the latest Galium Nitride (GaN) technology offer the best combination of high peak powers, high reliability, high efficiency, and soft degradation. High efficiency and high power are hallmarks of GaN technology, enabling SSPAs to challenge traditional tube-based amplifiers across the design spectrum. In addition the long lifetime from these devices, combined with the gradual degradation should individual devices fail, provide unparalleled service lifetime. Techniques such as bias modulation and linearization provide even better prime-power efficiency while still meeting the demanding requirements of pulsed or CW applications.
-
SSR -
Dwyer Instruments Inc.
Series SSR Solid State Relays amplify the current handling capability of a variety of sensors for controlling higher power loads. The relays are compact, totally encapsulated and impervious to shock or vibration.
-
Omron Industrial Automation
As well as being slim and thus saving panel space, The relays are very strong, have a large contact area and non-bendable pins. Connection to a PLC is easy and achieved faultlessly in a few seconds via click connectors. In addition, power switching in G3RV relays with DC outputs is managed by a MOSFET in the output, which has ideal heat dissipation characteristics.
-
Ranatec Instrument AB
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
J2110A -
PICOTEST Corp.
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
72-6635 -
Tenma
*Large LCD Display, easy to read*Characteristic of "A" frequency weighting network are designer to meet IEC 651 type 2*Fast time weighting characteristic mode*Build in adj. VR is available for easy calibration*Condenser microphone for high accuracy & long-term stability*Hold function to freeze the display value*Warning indicator for over and under range*LCD display for low power consumption & clear read-out even in bright ambient light condition*Durable, long-lasting components, including a strong, light weight ABS plastic case*Small and light weight design allow one hand operation*Low battery indicator*High quality with economical cost
-
Dalian Taijia Technology Co.,Ltd
Display: 10mm (0.4″) LCD (Liquid Crystal Display)● Function: LP , Leq ,LN.● Frequency range: 31.5Hz~8kHz● Measurement range: LP:30~130dB (A) 35~130dB (C) 35~130 dB (F) Leq :30-130dB LN .: 0-100%● Resolution: 0.1 dB● Accarcy:1dB● Memory: Maximum value (30groups)● Indicator: Low battery indicator● Alarm: electron● Connector:RS232C● Power supply: 4x1.5v AAA (UM-4 battery● Size: 236 x 63 x26 mm● Weight: 170g (including batteries)● Standed delivery:1.Main Unit................1pc2.Carrying Case............1pc.3.Operation Manual.........1pc.● Optional Accessories:1.ND9 sound level meter calibrator2.RS-232 and software3.External rela4.Bluetooth interface
-
LinkQuest Inc.
With the innovative technologies, LinkQuest's modems have achieved significantly increased data rate (up to 38,400 baud), lower power consumption and unprecedented robustness. All of LinkQuest's modems perform at a bit error rate of less than 10 which is equivalent to the quality of wire line communication. LinkQuest's extensive line of underwater acoustic modems outperform any competing products in technical aspects for both near-vertical, horizontal and extreme horizontal underwater environments.
-
Qref -
QSources BVBA
Precision omni-directionallity in all directions, horizontal and vertical plane. This source has a frequency range of application between 100 and 8000 Hz (third octave bands) Despite only weighing 1.4 kg and having a diameter of 105 mm, it produces a maximum sound power level of Lw 104 dB.
-
BSWA Technology Co., Ltd.
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
UV-SVP -
Valeport Ltd,
Designed for Underwater Vehicles where space is at a premium, the UV-SVP is based on the Valeport miniSVS. Incorporating Valeport’s class-leading time of flight sound speed sensor, a PRT temperature sensor and a 0.01% pressure sensor in a compact package weighing just 750 grams (in air), the lightweight titanium housing gives a depth rating of 3000m. A wide range (9-30V DC) isolated power supply and RS232 communications complete the package.
