Showing results: 1006 - 1020 of 7502 items found.
-
EB-76X -
Ceibo Inc.
* Emulates Philips Low-Pin Count Microcontrollers * Real-Time and Transparent Emulation up to 20MHz * 4K Emulation Memory * Real-Time Trace * Uses Philips Bond-Out Technology * 3.3V and 5V Operation * Software for MS-Windows * High-Level Support for Popular C-Compilers * On-Line Assembler and Disassembler * Emulation Header and Signal Testpoints * Power Supply Included * Serially linked to IBM PC at 115 Kbaud
-
DMM 125 -
Tecpel Co., Ltd.
7 Functions, 27 Ranges. Auto and manual ranging. 34 Segment fast bargraph. Auto Power OFF to save battery. 10 Amps and mA DC/AC fuse protected
-
AC1000A -
Aim-TTi
Provides an EN61000–3–2 compliant source1000W power capability at 230VUp to 4·4A rms load current and up to 10A peak currentsComprehensive overload protectionConnection via standard power connectors
-
Renesas Electronics Corp.
Renesas is a leading low-dropout regulator (LDO) supplier in low power handheld applications with world-class differentiated single and dual LDOs which have ultra-high PSRR up to 3MHz, low input voltage range, tiny packages, and ultra-low noise and quiescent current. Renesas' high current LDOs support up to 3A and have industry-leading fast load transient response, tightest voltage output accuracy at full load and over the full junction temperature, and lowest dropout voltage in its class.
-
CCI
*Tunable or band specific low loss combining of Tx and Rx*Typical 0.7dB insertion loss*Optional second duplexer can be installed in the same tray*High power handling with low IM and insertion loss*AISG 2.0 compliant
-
Praxsym
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
260-6XLM -
Simpson Electric Company
Designed for the special needs of solid-state circuitry measurements, the 260-6XLM has extra low power ohms ranges. It also offers all of the advantages of the standard 260 family, including a resettable overload protection circuit on the 260-6XLPM. Both versions come with batteries, manual and test leads with alligator clips.
-
CALEX
The 4:1 Input Voltage 75 Watt WDE includes remote sensing, ultra-wide output voltage trim, and remote ON/ OFF. The digital power management enables increased reliability, configurability, voltage / current precision and fault management.
-
CrossLink -
Lattice Semiconductor
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
-
Certus-NX -
Lattice Semiconductor
*Up to 39K logic cells, 2.9 Mb embedded memory, 56 18 x 18 multipliers, 192 programmable I/O, one lane of 5 Gbps PCIe, two lanes of 1.25 Gbps SGMII, two ADCs (each 12-bit, 1 MSPS).*Packages as small as 6x6 mm, and in ball-pitch options of 0.5 and 0.8 mm.*Power modes – User selectable Low Power vs. High Performance modes, enabled by FD-SOI programmable back-bias.*Design security – ECDSA bitstream authentication, coupled with robust AES-256 encryption.*Instant-on configuration – I/O configures in 3 ms, and full-device as fast as 8 ms.*Available in Commercial, Industrial and Automotive (AEC-Q100 qualified) temperature grades.
-
ICE40 LP/HX -
Lattice Semiconductor
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
CrossLinkPlus -
Lattice Semiconductor
*Instant-on (< 10 ms) configuration with integrated flash memory*Integrated flash enables flexible reprogramming in the field*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per port*11 programmable, source synchronous I/O pairs for camera and display interfacing*Available in small 3.5 mm x 3.5 mm BGA package with 0.4 mm pitch*Comprehensive library of IP and reference designs, compatible with CrossLink
-
-
Bank Elektronik
Potentiostat Wenking MP 04T, max. current 400 mA, max. voltage 25 V, output power 10 W, reference electrode input 1012 Ohms, slew rate 10 V/ µs, 1 control input, floating current output, buffered potential output, control range ± 10 V external, internal control voltage source ±2 V, rise time constant (closed loop, ohmic load) 1 µs typ., dimensions 165 x 105 x 165 mm (w x h x d), weight 1.4 kg
-
Analog Devices Inc.
Analog Devices provides a wide range of low power RF transceivers covering sub-GHz and 2.4 GHz frequency bands. Drawing on over 40 years of experience designing high performance RF ICs, the ADF7xxx family of transceivers delivers industry-leading RF performance combined with ultralow power consumption. Our latest transceivers incorporate configurable packet handling capability for proprietary and industry standard protocols to address emerging Internet of Things requirements. As faster time to market grows in importance, evaluation platforms such as the latest ADF7xxxMB4Z will be critical to kickstarting software development.