Resistance
that which keeps current from flowing freely.
See Also: Resistivity, Resistance Standards, Resistance Meters, Resistance Test, 4-wire
-
product
Full- Channel Resistivity Meter
ZZ Universal 64
ZZ Resistivity Imaging Pty. Ltd.
Comprehensive resistivity instrument. 61 channel system.
-
product
SPD AC & DC Thermal Stability Test Equipment
Shanghai Guantu Technology Co., Ltd.
1. Computer control measurement, PLC control;2. Equipped with sudden voltage capability, suitable for thermal stability tripping test under high current conditions;3. Increase the high-power resistance box;4. The interface is friendly and beautiful, and can reflect the running status of the system in real time; .5. Automatically draw voltage, current and temperature curves;6. The system performs multi-point temperature detection in real time;7. Timing sampling and recording function, which is convenient for users to view temperature values at different times and compare data;8.2 times Uc leakage current test function to check the tripping reliability of the product;9. Built-in test box;10. RS232 communication interface, can realize remote control.
-
product
Precision Capacitance Meter
TH2638B
Changzhou Tonghui Electronic Co., Ltd.
TH2638 series is a new precision capacitance meter with higher test frequency. With small size and portable appearance, it is convenient for use on the shelves. With basic accuracy of ±0.07%, loss accuracy of 0.0005, test frequency up to 1MHz, 4.3-inch LCD screen, selectable Chinese-English operation interface, TH2638 series is easy to operate and provide fast and reliable test for ceramic capacitor production. Also, it can test all kinds of capacitors from low value to high value. The results of testing one capacitor for several times are quite stable and accurate, even for lower value capacitors. The tester is compatible with SCPI command set, and configured with manipulator and scanner interface, the scanner interface can scan the open/short/ load error calibration in each channel, 256 channels at most. In low frequency, there is signal level compensation function. When the impedance is very small, the internal resistance in signal source and test cable will cause the voltage on terminal of DUT lower than the set range, then this function will adjust the level to the set range.
-
product
Standard 1.50 (43.00) - 4.00 (113.00) High Performance Lead Free Probe
LFRE-25I15-4
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Oil Resistivity & Tan Delta Test Set-Up
This testing set is an automated instrument, widely used for measuring electrical characteristics of insulating liquids, transformer oil and other insulating material samples.
-
product
Rugged Cabinet
MS Series
The M-Series MIL-STD Cabinet offers a high level of integrity with its all-welded 12 gauge steel frame construction, and eight, 3-dimensional support braces (12 gauge), providing added resistance to demanding compressive and torsion loads.
-
product
Multimeters
A multimeter is a measuring instrument whose function is to measure electrical quantities such as voltage, current, resistance, capacitance and inductance.They are a perfect measurement solution in various fields of industry.
-
product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 52.4kΩ
40-298-133
The 40-298-133 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Loss Tangent M in Dielectric Oil
TAND220A
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
product
Surface Resistance Meter
SRMETER2
The Surface Resistance Meter is a wide range, multi-scale, auto-ranging meter. This meter is appropriate for auditing static control work surfaces.The meter is 9V battery powered and simple to use.NIST Calibrated
-
product
A-A-S General Purpose Probes
Current Rating (Amps): 2Average DC Resistance lower than (mOhm): 30Test Center (mil): 39Test Center (mm): 1.00Full Travel (mil): 30Full Travel (mm): 0.76Recommended Travel (mil): 20Recommended Travel (mm): 0.51Overall Length (mil): 310Overall Length (mm): 7.87Rec. Mounting Hole Size (mil): 31.5Rec. Mounting Hole Size (mm): 0.80Recommended Drill Size: #68 or 0.79 mm
-
product
Industrial Paint & Powder Thickness Gauge
415
Incredibly fast (60+ readings per minute), reducing inspection times, increasing productivitySwitches instantly between ferrous & non-ferrous substrates without interruption1Measures cured paint & powder coatings up to 1000μm (40mils)Zero or smooth (2 point) calibration ensures accuracy on smooth & thin coated substratesEasy to use, ergonomic design provides maximum comfort for continuous useLarge easy to read values in microns or milsAuto rotating large colour display provides clear visibility whatever the angle of measurementScratch, solvent & water resistant display protects against the elementsRugged & resistant to dust or powder coatings equivalent to IP64, ideal for modern industrial & powder coating environmentsTransfer live data via USB or Bluetooth® to ElcoMaster® for instant report generation
-
product
Touchscreen Panel 1.9GHz PC for Harsh Environments
PPC65B-1x series
Advanced IP65-rated Panel PC delivering high reliability and an extended operating temperature range in a thin, fanless design. The PPC65B series offers a rugged design for extreme environments and industrial IoT applications ranging from -20ºC to +70ºC. 1.9 GHz Quad-Core Intel® Atom™, E3845 processor, Up to 8 GB of RAM, Supports Linux, Windows 10 Operating Systems, Fast Graphics at High Resolutions • Five-wire resistive touchscreen • Resolution: 1024 x 768 / 1280 x 1024; 5 screen sizes 10.4" - 19".
-
product
Blanket Flammability Tester
TESTEX Testing Equipment Systems Ltd.
Blanket Flammability Tester, to determine the ignition resistance property of blanket fabrics(blanket fabric burn test). Blanket Flammability Tester complies with ASTM D4151, etc.
-
product
Mini Digital Multimeter
HH2103
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection
-
product
Lightning Surge Generator
SKS-0510I
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0510I fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; it provides pulse test voltages up to 10kV, which can meet the severity levels of various product standards; Covers the two surge waveforms specified in the standard 1.2/50ms (short-circuit current is 8/20μs) and 10/700ms (short-circuit current is 5/320μs), and a variety of internal resistances are built-in for customer use; Two kinds of surge waveforms, and built-in a variety of internal resistances for customers to use; AC and DC samples can be tested, the rated current can reach 32A.
-
product
LIGHT RANGER MUTT
TT9103
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe
LFRE-1L18-4
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Passive Probe
PP011-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
Hybrid Wound Component EST Scanner
19035
Chroma Systems Solutions, Inc.
The quality verification test items for Wound Components consist of AC/DC Hipot tests and Insulation Resistance (IR) tests. Chroma integrates the above tests into the Hybrid 19035 Wound Component EST Scanner series to perform safety tests for motor, transformer, and heater related wound products. The wound component manufacturers performing quality verification testing will not only have reliable quality, but also can control product quality efficiently.
-
product
Insulation Resistance Tester 600V AC/DC
IRT803
UEi Test & Measurement Instruments
The IRT803 Digital Insulation Resistance Tester has a 600V AC/DC measurement capability and auto ranging. It features a backlit display that shows test function and measured value. And is backed by a 1-Year limited warranty.
-
product
Standard Digital Multimeter - Auto Ranging
MM39
The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.
The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.
-
product
Earth Resistance & Resistivity Meter
MRU-21
* earth resistance measurment with 3-pole method, * measurement of continuity of equipotential bondings and protective conductors with auto-zero function - with current 200mA, * resistance measurement using 2-pole method.
-
product
Alternate 2.58 (73.00) - 6.00 (170.00) High Performance Lead Free Probe
LFRE-25Z1-6
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Insulation Tester
AD-225
3 Measurement voltage range: 500 V; 1000 V and 2500 V, Control of measuring voltage during measurement, Insulation measurement up to 100 G W, Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging,
-
product
Capaciter Tester
KS-1600
Konstar Electric Industrial Co., Ltd
It is a dial instrument, and has the stable function and high reliability. It is driven by the battery. The instrument makes use of the indicator plate(102*79mm), thus displays clearly.This instrument can test the data of on-line capacitive resistance and on line impedance. It is an excellent instrument and an ideal tool for the people in labs, factory and household. When testing the mounted capacitor, it does net need to be completely out of power nor do the meter, and the meter can be testing continuously.
-
product
Contact Resistance Meter
CRM 200B
CRM 200B directly measures micro-ohm values at 100 Amps DC under live switchyard conditions.CRM 200B is specially designed to reliably measure contact resistance of circuit breakers, isolators, busbar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards upto 765 kV.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 62.1Ω
40-253-111
The 40-253-111 is a programmable resistor module with 1 channel which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Bias Ball Probe
POGO-1Z-10
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Micro Coax, Contact, Receiver, RG179
610140103
Primary mating contact 610141103. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 75ΩFrequency Range DC – 2 GHzVSWR 1.39 @ 2 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outerCable Specifications RG179Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
