Product

Film Impact Tester

DRK136B

-

Shandong Drick Instruments Co., Ltd.

DRK136B - Shandong Drick Instruments Co., Ltd.

DRK136B Film Impact Tester is applicable in the precise impact resistance test of plastic films, sheets, laminated films, rubber and other nonmetal material.

Product

Flame & Other Plastics Testing

-

Educated Design & Development, Inc.

Educated Design & Development, Inc.

Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.

Product

Automatic Wire Test Set

AWTS

-

Eclypse International

AWTS - Eclypse International

The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.

Product

600A Digital Clamp Meter

7128C

-

Peaceful Thriving Enterprise Co Ltd

7128C - Peaceful Thriving Enterprise Co Ltd

This is an auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC/DC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity, frequency and non contact voltage sensing. Sub switch included Function Select, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Hz/Duty Cycle, Illumination and Back-light.

Product

Accessories

-

Smiths Interconnect

Smiths Interconnect

The proprietary MicroClip™ is a low-profile, low-mass spring loaded mechanical assembly that offers a rugged optical connection that is resistant for shock and vibration and is suitable for harsh environment. The  MicroClip ferrule design has proven it can withstand a 1 kg live traffic fiber pull test on a 12-fiber ribbon cable pigtail mated to its LightABLE™ products (40G SR4 and 120G SR12), without any signal performance degradation. This result exceeds by a factor of 2 the requirements of Telecordia GR-468-CORE Fiber Integrity Side Pull Test and confirms the reliability of the Reflex Photonics fiber ribbon interface with the LightABLE and its MicroClip ferrule.

Product

Self Powered Active Load

TBOH02

-

TekBox Singapore Pte. Ltd.

TBOH02 - TekBox Singapore Pte. Ltd.

The TBOH02 is a self powered, precision active load. It does not need a separate supply voltage and operates as low as 2V. Its features include constant resistance and constant current mode. A 10 turn potentiometer with dial, a range switch and a precision reference enable accurate setting of current or resistance. Furthermore it can be controlled by an external voltage.

Product

Field thermal needle system for thermal resistivity / conductivity measurement

FTN01

-

Hukseflux Thermal Sensors B.V.

FTN01 - Hukseflux Thermal Sensors B.V.

The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.

Product

Shock Test System, Battery Test

-

Guangdong Bell Experiment Equipment Co.,Ltd

Guangdong Bell Experiment Equipment Co.,Ltd

DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.

Product

Near Field Probes 30 MHz up to 3 GHz

RF2 set

-

Langer EMV-Technik GmbH

RF2 set - Langer EMV-Technik GmbH

The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.

Product

Overmolded Cable Harnesses

-

Teledyne Marine Cable Solutions

Teledyne Marine Cable Solutions

TCS has the ability to provide fully sealed, overmolded harnesses and harness elements as the ultimate connection for severe use, extreme weather, or resistance to water, fuels, solvents and UV rays.

Product

Digital Megohmmeter

800

-

ACL Inc.

800 - ACL Inc.

The ACL 800 Digital Megohmmeter is a dependable and easy-to-use audit kit that is designed to test static dissipative surfaces for electrical resistivity and resistance according to industry standards such as ANSI/ESD test methods S4.1, S7.1, and ASTM D257. Tests are easy to perform with or without the 5lb probes. Use optional concentric ring probe for conformance to STM11.11.

Product

Corrosion Testing

-

Global Testing Services Inc.

Global Testing Services Inc.

The salt spray test is a standardized test method used to check corrosion resistance of coated samples. Coatings provide corrosion resistance to metallic parts. Since coatings can provide a high corrosion resistance through the intended life of the part in use, it is necessary to check corrosion resistance by other means. Salt spray test is an accelerated corrosion test that produces a corrosive attack to the coated samples in order to predict its suitability in use as a protective finish.

Product

OHMMETERS

DOT-1000-2

-

Criterion Instruments Limited

DOT-1000-2 - Criterion Instruments Limited

Model DOT-1000-2, is an ac four-terminal ohmmeter to be used for the measurement of dynamic ac resistance of batteries, fuel cells and other voltage sources.

Product

IK Level Tester

IK07-10

-

Lisun Electronics Inc.

IK07-10 - Lisun Electronics Inc.

IK ratings are defined as IKXX, where “XX”  is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).

Product

Resistance Tester

METRISO® 3000

-

Wolfgang Warmbier GmbH & Co. KG

METRISO® 3000 - Wolfgang Warmbier GmbH & Co. KG

Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportA barcode scanner can be used in order to record measurement points before testing

Product

Battery Capacity Analyzer with record storage

603B

-

B&K Precision Corporation

603B - B&K Precision Corporation

The 603B handheld battery capacity analyzer tests 6 and 12 volt sealed lead acid batteries with capacities up to 100 ampere hour (Ah). Test results include voltage, state of charge, and internal resistance. This analyzer also features a built-in USB port and internal memory to store battery information, test configuration, and measurement results for up to 50 batteries.