Bias Test
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
Test Port Adapter
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
Scienlab Battery Test System – Module Level
SL1001A Series
Test System
The SL1001A and SL1006A Battery Test Systems – Module Level Series help you emulate sink and source for battery modules for automotive and industrial applications.
-
Product
Test Port Cable, 1 Mm
11500I
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 8.8-cm cable featuring a return loss of 17 dB minimum.
-
Product
2-Quadrant Source/Measure Unit for Functional Test, 20 V, 1 A or 6 V, 3 A, 20 W
N6782A
Functional Test
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
Product
Advanced SoC/Analog Test System
3650-EX
Test System
Chroma 3650-EX is specifically designed for high-throughput and high parallel test capabilities to provide the most cost effective solution for fabless, IDM and testing houses.
-
Product
SoC Test System
T2000
Test System
SoC devices require small-lot high-mix manufacturing methods in the present era of rapid generation change. Semiconductor makers struggle with requirements to replace their testers on a 2-3 year cycle. The T2000 addresses their needs by enabling rapid response to market needs with minimum capital investment.
-
Product
EBIRST 50-pin D-type To 37-pin D-type Adapter
93-005-418
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Automated Aerospace and Defense Test
test
Obsolescence management, evolving RF requirements, and design for test (DFT) challenges every test organization in the aerospace and defense industry. Organizations are transitioning from rack-and-stack box instruments and closed-architecture automated test equipment (ATE) systems to smarter test systems built on a modular platform that scales to meet current and future needs.
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Medalist i1000D
U9401B
In-Circuit Test System
The Keysight Medalist i1000D is now even better. Improving from its previous state of an analog-only ICT, the new digital release of the system now features per pin programmable digital cards and a whole new set of intuitive software graphical user interfaces (GUIs) that makes programming and development effortless.
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Hybrid Single Site Test Handler
3110
Test Handler
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
Compact Functional Test System
E2230C / TS-5040
Functional Test
The Keysight TS-5040 functional test system is a robust, and reliable test system that ensures an economical ownership experience. When coupled with Keysight software such as KS8400A PathWave Test Automation with KS8328A PathWave Test Executive for Manufacturing (PTEM) or TestExec SL with TS-5000 libraries, it provides a streamlined development process and accelerated deployment. The TS-5040 seamlessly integrates into heavily automated production areas. It is a minimalistic one-box solution for automotive and industrial applications that saves valuable rack and floor space.
-
Product
NI Automated Test Software Suite
test
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
Product
6TL24 Combinational Base Test Platform
H71002400
Test Platform
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Test Systems
Test System
Ball Systems delivers best-in-class automated testing systems, software programming, integrated manufacturing systems, and industrial engineered solutions. Our team has former corporate test engineers, quality assurance engineers, industrial engineers, and test managers who have decades of experience to assist customers in meeting their automated test challenges by offering:
-
Product
VR/AR/MR Calibration Platform
Test Platform
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
Product
PCIe 5.0 Test Platform
PXP-500A
Test Platform
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
Portable, Integrated O-Level Test Platform
Guardian™
Test Platform
Guardian is a ruggedized automated testing platform that quickly and accurately verifies the operational readiness of complex electronics systems in aircraft, ships, and vehicles.
-
Product
High Temperature Component Test Fixture
16194A
Test Fixture
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
In-Circuit Test System Calibrations
Test System
Regular calibration is essential to ensure accuracy and reliability in testing. Forwessun offers precise calibration services tailored to your test systems, verifying that all components meet industry standards. Our calibration services maintain peak accuracy and compliance, so you can be confident in your system’s performance for any testing application. Choose from one-off calibrations or scheduled service contracts to meet your needs.- HP3070 - Agilent- Keysight - GenRad- Teradyne
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Lower-Cost Small Footprint In-Circuit Test System
TestStation LHS
In-Circuit Test System
The TestStation LHS in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne’s popular, award winning TestStation product family. Compatible with existing TestStation LH fixtures.TestStation LH features the voltage accuracy and backdrive current measurement embedded in Teradyne’s SafeTest protection technology for accurate, reliable and safe powered-up testing of new low-voltage software.
-
Product
Universal Test System
LEON System
Test System
A universal ICT, FCT, ISP and Boundary Scan platform.Based on the ABex platform, which directly integrates Konrad analog bus technology and PXI/PXIe in one chassis, the LEON platform can be configured to solve various test challenges. Due to this architecture only one system provides the complete test flow combining ICT, ISP, Boundary Scan and FCT.Various form factors and configurations allow a perfect combination between cost, speed and test coverage. The modular architecture provides the possibility to reconfigure or upgrade the systems based on your test needs.The LEON System software provides a powerful development and test execution environment which directly supports NI TestStand. All systems and components could be integrated into third party software using supplied APIs.
-
Product
Mini LED Backlight Module Automatic Optical Test System
7661-K003
Test System
Chroma 7661-K003 Mini LED Backlight Module Automatic Optical Test System contains a 71803-2 2D color analyzer to measure chromaticity and brightness
-
Product
True Concurrent Test
TestStation Duo
Test System
The TestStation Duo is a true concurrent test system with independent test modules providing fast in-circuit test throughput and lowering high-volume production costs.It effectively doubles the test throughput of conventional in-circuit test systems, without doubling capital equipment costs or increasing manufacturing floor space, by combining two complete and independent test modules inside a single tester frame.
