Simulation Testing
See Also: Simulation, Simulators, Simulation Software
-
Product
Environmental Simulation Testing
-
Innovative Testing Solutions, Inc.
We have multiple chamber capabilities of simulation most environmental conditions. Our chamber range in capacity from 1 ft3 to 64 ft3 volume. Specialty chambers include air-to-air thermal shock, inert gas injection oven, high/low pressure water spray and direct-injection LN2 chambers.
-
Product
Environmental Simulation Testing
-
MET's Environmental Simulation Labs, on both coasts, employ numerous environmental chambers, including several large walk-in chambers. Hydraulic and electro-dynamic shakers are used for a wide range of vibration testing, from ISTA packaging to seismic compliance testing. MET's hydraulic vibration systems are capable of full level (Zone 4) seismic simulation.
-
Product
Steam Aging Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Steam aging test chamber is a climatic test machine used to judge the products performance to resist extreme circumstance under high temperature, high humidity and high pressure during the transportation, storage and usage. The principle is very simple, water in the tank is heated turning into steam to form a simulated test environment under specified temperature and humidity. Specimens are placed into the drawers of machine to carry out test lasting for preselected time. It is applicable to electronic connectors, semiconductor IC, transistor, LCD, diodes, resistances etc.
-
Product
Channel Emulator
-
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
Product
Motor Driven Actuator
NJ-SERVO Series
-
The NJ-SERVO electric motor driven actuator utilizes an electric motor drive system. High accuracy test control is enabled by a special servo motor and stroke displacement measurement sensor. In addition, the system configuration is simpler in comparison to hydraulic actuators, so it is easy to maintain, and achieves power savings and space savings. This system accommodates a wide range of tests with a high degree of expandability. This includes everything from endurance evaluations of the main body and assemblies of automobiles, aircrafts, and other transportation equipment to endurance evaluations of stand-alone parts; from multi-axis tests combining multiple actuators to uniaxial tests; and from sine waves to working waveform simulation tests.
-
Product
Fuel Display Unit Tester
MS 1125
-
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
Product
PXI Thermocouple Simulators
-
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
Product
Cross Browser Testing
BrowseEmAll
-
Live Testing, Screenshots, Code Analytics & Selenium Integration On Your Local Machine. Every browser is just one click away. Mobile Simulators. Test for iOS, Blackberry, Windows Phone and Android. Screenshots. Find layout issues with screenshots. Automated Compatibility. See problems directly in your Code. Side by Side Test browsers and mobile devices simultaneously. Test Automation. Run Selenium Tests Out Of The Box.
-
Product
PMC Intelligent Interface Card
IIB-1553-PMC
-
The IIB-1553-PMC is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the PCI Mezzanine standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card.
-
Product
Transmission Performance/Endurance Test System
-
This system is suitable for vehicle drive test with only the transmission unit in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling engines, tires or vehicles other than transmission. The engines, tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
Aircraft Data Systems
System
Aircraft data systems for commercial and military applications, including Aircraft Interface Devices (AID), avionics I/O computers, avionics test & simulation interfaces, and Embedded avionics interfaces.
-
Product
Electric Servomotor Steering HILS Tester
-
This device is a complex simulation test device completed by the operation of the steering system performance / durability test machine and the hardware in the loop systems (HILS) system.
-
Product
Environmental Simulation
-
During the development phase of new products, we analyze the weak points in simulation tests and test the products for environmental influences. The relevant standards are used as the basis for the simulation tests.
-
Product
High Speed DC Electronic Load
6330A series
-
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Test Package
-
Shenzhen Bonad Instrument Co., Ltd.
We can provide a variety of different specifications of freezing load test packages, including AHAMHRF-1 2007/ SASO 2664-2007 Sawdust freezing test package, AS1731.4-2003 Australian frozen Load Test Package, AS72-2005 North American Commercial Refrigeration Load Simulation Test Package, IEC 62552 Test Package for Freezing Load Testing in Refrigerators. In addition, we can also provide customization according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
PXIe Avionics Interface Cards
Interface
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
Product
Full Range Photodiode Array UV-VIS-NIR-SWIRLaboratory Spectroradiometers
-
The SR-Series of full range laboratory spectroradiometers is ideal for a wide range of applications, including Solar radiance and irradiance measurements. Solar simulator test and classification. LED, laser, light source metrology. Radiometric calibration transfer. Remote sensing applications.
-
Product
Simulation and Testing Solutions
LMS
-
Siemens Digital Industries Software
LMS simulation and testing solutions help manufacturing companies manage the complexities of tomorrow’s product development by incorporating model-based mechatronic simulation and advanced testing solutions in the product development process. Our products and services tune into mission-critical engineering attributes – ranging from system dynamics, structural integrity and sound quality to durability, safety and power consumption.
-
Product
2-way Radio Signaling Test Software
Tone Generator
-
The new PC-based test software for RF communications engineers and technicians. Flexible, accurate code synthesizer for simulation and testing of 2-way radio systems, repeaters, remote control, ANI, Paging and more.No external hardware required.
-
Product
SpaceWire-USB Brick Mk3
326
-
The SpaceWire Brick Mk3 is a USB 3.0 (also works with USB 2.0 and USB 1.1) to SpaceWire interface device that is suitable for use in all stages of SpaceWire equipment development: initial SpaceWire evaluation, instrument simulation, control system simulation, unit testing, integration support, and EGSE. The SpaceWire Brick Mk3 provides two SpaceWire interfaces, support for high speed data transfer, the capability to inject various types of errors on demand, the ability to transmit and receive time-codes and act as a time-code master, and comes complete with highly optimised host software for low latency transmission of SpaceWire packets directly to and from the host PC.
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
Intelligent Interface Card
IIB-1553-CPCI
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.The IIB-1553-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes,with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface.2 Mbytes of dual ported RAM are supplied as standard. The board is supplied with C drivers in source code and Windows menu driven software.
-
Product
Computer simulators
-
There are three computer simulators offered by INFRAMET:*SIMTERM - computer simulator of thermal imagers,*VIRTEST - computer simulator of test proces thermal imagers ( MRTD measurement)*NIGHTMET - computer simulator of image intensifier tubes
-
Product
Hydrogen Testing Solutions
-
The widespread introduction of hydrogen is a necessary and essential part of the path to a climate-neutral future. AVL is ideally equipped to support and help shape this transfer. In terms of content, we provide extraordinary expertise in the fields of engineering, simulation and testing and act as a reliable innovation and development partner. With our test solutions, we support you specifically with your challenges, from development, through industrialization, to further operation. Depending on the technological maturity of your product, the test solutions offer you full flexibility within the planned development tasks or a customized proportion of supporting and automated functions, if quality assurance in the production environment is involved. The guarantee of safe operation is obligatory and is of course also mapped.
-
Product
Test & Simulation Interface for PCI-X
PCI-X-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI-X
-
Product
Bidirectional DC Power Supply + Regenerative Load
62000D
-
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
Product
HPx-310 Radar Signal Output Card
-
The HPx-310 Radar Signal Output card is a replacement for the HPx-300, form, fit, and function. It generates representative radar signals for system testing, simulation, training or radar video streaming. Under software control, the card generates radar video, trigger and azimuth signals similar to those generated by real radars.
