Simulation Testing
See Also: Simulation, Simulators, Simulation Software
-
Product
P104 Synchro/Resolver Simulation Board
73DS2
Simulator
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
Product
NTS Platform
Test Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
Product
LTE/LTE-Advanced Analysis Using NI PXI RF Test Instruments
NI-RFmx LTE/LTE-Advanced
Test Instrument
Highly optimized RF measurement experiencePerform physical layer analysis on LTE cellular signals including MODACC, ACPR, CHP, OBW, and SEMIncludes support for TDD, FDD, and LTE-Advanced signals specified in 3GPP standards release 12Simple access to advanced measurement parallelism
-
Product
Synchro/Resolver Simulator, Programmable
5330A
Simulator
NAI's 5330A Synchro/Resolver Simulator is a rack-mount or bench-top instrument featuring integrated touch-screen controls and input terminals. This model represents a major step forward as it uses digital technology to produce Synchro and Resolver outputs. Improved flexibility is provided by two fully independent outputs that can be used to simulate two separate Synchro or Resolver signals simultaneously, or can be combined to operate as two-speed outputs. The versatility of this device has been substantially increased by incorporating dynamic modes that enable servo systems to be tested under various simulated stringent field conditions.
-
Product
Portable, Integrated O-Level Test Platform
Guardian™
Test Platform
Guardian is a ruggedized automated testing platform that quickly and accurately verifies the operational readiness of complex electronics systems in aircraft, ships, and vehicles.
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
ARINC 818 Tester
Test Platform
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
Product
CPE Design Verification System
Jupiter 310
Test System
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
4, 8, 16 And 32 Channels ARINC429 Test & Simulation Module CompactPCI/PXI (3U)
ACXX429-3U-x
Simulator
The ACXX429-3U-x is a functional replacement formodel ACX429-3U-x.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
43-752A-111
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Custom Test System Solutions
Test System
No time to think about test? One-size-fits-all testers not ideal? Existing solution no longer fits your needs? Then count on integrated test solutions from Astronics. We’ll assist you with your test strategy and your test system, setting you on the path to market at a pace and ROI that ensures your program success.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
Solar Array Simulator
62000H-S series
Simulator
The latest programmable solar array simulator power supply 62000H-S Series released by Chroma provide simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000H-S provides an industry leading power density in a small 3U high package. The solar array simulator is highly stable and has a fast transient response design, which are both advantageous to MPPT performance evaluation on PV inverter devices. The 62000H-S Series have many unique advantages including high speed & precision digitizing measurement circuits with a 100kHz A/D, 25kHz D/A controlled I-V curve and a digital filter mechanism. It can simulate an I-V curve accurately and response the mains ripple effect from the PV inverter. In addition, the built-in EN50530/Sandia SAS I-V model in the standalone unit can easily program the Voc, Isc, Vmp, and Imp parameters for I-V curve simulation, without a PC controller.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
Test Port Cable
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Die Test Handler
3112
Test Handler
Chroma 3112 is a productive pick & place handler for high volume single- or multi-site bare die testing.
-
Product
4, 8, 16 And 32 ChannelARINC429 Test And Simulation Modulefor PCI Express
APE429-x
Simulator
ARINC429 Test and Simulation modules with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s. The APE429-x is a functional replacement for the models API429-x/APX429-x.
-
Product
Audio and Acoustic Functional Test Solution
Functional Test
With the growing popularity of Internet of Things devices worldwide, many electrical products are adopting voice commands as their user interface. This means that acoustic and audio test challenges are likely to impact more products than ever before. Test teams must meet extended test coverage requirements to ensure product quality while maintaining throughput and operational efficiency. For a solution to meet these sorts of demands, it must:
-
Product
Battery Simulator
Battery Simulator
The battery simulator is used for testing satellite power supplies and is used in combination with a Solar Array Simulator and load systems (consumer simulation) for the validation and commissioning of satellite power supplies. Loads and power supplies in the battery simulator are operated in combination to represent a 2-square function and to simulate both charging and discharging of the battery.
-
Product
Test & Simulation Interface for PCI
PCI-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI
-
Product
Scienlab Battery Test System - Cell Level
SL1007A
Test System
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Bluetooth RF Test System
FRVS
Test System
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
Product
Laser Diode Burn-in Reliability Test System
58604
Test System
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
VLSI Test System
3380
Test System
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
Multiple Module Serial Bus Test Instrument
Bi4-Series
Test Instrument
The wide variety of serial buses used in defense and aerospace applications typically requires multiple single-purpose instruments. Too often, they are difficult to reconfigure in order to test a different application.The Bi4-Series provides all the capabilities needed for complete communications bus access test for up to four serial buses used in board level (SRA/SRU) and box level (WRA/LRU) equipment—all in a single VXI module.The instrument includes test applications, industry-compliant software drivers and hardware enabling straightforward integration into automatic test systems.With the configuration flexibility needed to effectively test every bus format used in defense and aerospace applications, the Bi4-Series instrument plays a key role in reducing implementation time and test system cost.
-
Product
Antenna Test System
ATS1000
Test System
Offering measurements on active and passive devices - supporting also extreme temperature testing. 5G is all about data, speed and reliability using high frequency millimeter wave bands. The lack of conventional external RF connectors makes 5G antenna characterization challenging. 5G antenna, chipset and UE manufacturers as well as wireless market operators need a viable solution for research, diagnostics and debugging up to type approval.
-
Product
Mini In-Circuit Test System
U9403A
In-Circuit Test System
The Keysight Mini ICT is a true in-circuit test unit in the rack that can be used standalone or integrated. It comes with a full set of Keysight ICT test features, from VTEP vectorless test, Cover-Extend Technology, to digital library tests and boundary scan. The unmuxed per-pin programmable digital engine makes test development really flexible and easy, especially in a situation when device conditioning is needed in functional test.
-
Product
Automatic Test System
Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
