Discharge
-
Product
76kWh Lithium Battery 384V 200AHSolar Energy Storage LiFePO4 battery System
SPVLI-76KWH
-
Zhejiang Sandi Electric Co., Ltd
SANDI ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
-
Product
Battery Analyzers
CA 1550 – Military Version
-
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
Product
Ultrasonic Leak Detector
ULD-410
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-410 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure.
-
Product
Transformer Ratio Meters
Handheld Turns Ratio & Winding Resistance Tester TWR-H
-
TWR-H is a handheld, battery operated, fully automatic test set specially designed for turns ratio, phase shift, excitation current and winding resistance measurements of transformers. It can also perform demagnetization of these transformers. Transformer turns ratio is determined by applying AC voltage across high voltage winding, accurately measuring AC voltage across the corresponding unloaded transformer winding, and then displaying the ratio of these voltages. User can enter a transformer’s nameplate voltages, so that turns ratio deviation can be calculated. This feature eliminates any error otherwise caused by an operator’s manual calculation. TWR-H compares measured turns ratio with the nameplate ratio and prints out the % of error for each test. Transformer winding resistance is determined by injecting DC current through a winding, accurately measuring DC voltage across the winding, and then calculating resistance as the ratio of voltage and current. The device generates true DC ripple-free currents. Both the injection of the current and the discharge of energy from transformer magnetic circuit are automatically regulated.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
RC Meters
-
Provides the. capacitance to be measured at a frequency which is reciprocal to the. product of the discharge resistance and the measured capacitance.
-
Product
DC Electronic Loads
-
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
Miniature, Battery Powered, Stand Alone Pressure and Temperature Data Logger
PRTemp101A
-
The PRTemp101 is a miniature, battery powered, stand alone pressure and temperature data logger. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 8,191 measurements per channel. The storage medium is non-volatile solid state memory, providing maximum data security even if the battery becomes discharged.
-
Product
PXI Based Multifunction Measurement and ICT Instrument
PXI-501
Multifunction Switch/Measure Unit
The PXI-501 is a multifunction measurement instrument for functional and in-circuit measurements.It combines two parametric measurement units with a digital voltmeter, a high voltage current source and a discharge unit. This powerful combination makes it the ideal instrument for classical analog in-circuit test and manufacturing defect analysis with additional functional test capabilities.With it’s fast sampling rate of up to 4MSps it speeds up measurements and is capable of measuring and generating AC signals up to 100kHz.To enhance the PXI-501 capabilities it can be combined with an ABex TM-501 or an ABex TM-404. The ABex TM-501 enhances the in and output range of the PXI-501. Furthermore, it provides a shunt current measurement upgrade. In combination with the ABex TM-404 it’s a complete in-circuit test solution with 86 channels in one ABex slot. For sure it can be upgraded to 2838 test points in one rack by simply adding additional matrix modules.With the above-mentioned terminal modules, the PXI-501 is able to act as a ABex system controller, so that no additional controller is required in the cassis.
-
Product
Inrush Current Generators for Zno Production Line
-
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
Product
Partial Discharge Tester
19501-K/19500
-
Chroma 19501-K partial discharge tester combines hipot test and PD (partial discharge) detector functions in one instrument. The device is capable of a maximum 10kV AC output with leakage current measurement range of 0.01uA and a minimum partial discharge detection of 1pC. The tester is specifically developed to test high voltage semiconductor components and high insulation materials.
-
Product
Capacitor to Dim
DAM1
-
Lifasa - International Capacitors, SA
DAM switching capacitors are used to protect semiconductors (IGBT transistors). These are charged and discharged repeatedly with high current peaks. This series is especially indicated for applications that require high capacities at high voltages.
-
Product
Electrostatic Products
-
We offer electrostatic measurement instruments for electrostatic discharge (ESD) and high-performance applications. Select from our reliable electrostatic sensors and detectors, voltmeters, charge plate monitors, and surface resistance/resistivity meters.
-
Product
Dielectric Loss Tangent Testing Instruments
-
Insulation materials in electrical equipment are used between a pair of electrodes; therefore it can be expressed as capacitors. Applying AC voltage to a capacitor with insulation materials causes an energy loss due to the leak current, the dielectric polarization, and the partial discharge. Because of this, the phase of the capacitor current is more delayed than that of a zero-loss current (reactive current) flowing in an ideal insulation material. The delay angle is called "Dielectric Loss Angle", and the tangent is "Dielectric Loss Tangent" (tanδ). Please refer to the technical guide explained in detail.
-
Product
Vacuum Discharge Test Equipment
DAC-VD-1
-
DAC-VD-1 can locate defective points such as scars or pinholes on stator coils and wires easily.By applying voltage in a vacuum chamber, the electric arcing from a defective part can be discoveredvisually in a short time. DAC-VD-1 can be used widely in variety of applications from product developments to outgoing inspections.
-
Product
H-Type Surge Generator
-
Shanghai Guantu Technology Co., Ltd.
Features of H-type surge generator1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
Product
Automotive Battery Testers
-
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
Product
Dirty Bomb Detection Jamming System
-
Security Intelligence Technologies, Inc.
The SSR-7000 consists of a radiation detection system that operates in concert with a MM Wave body scanner and an electronic countermeasure IED Defeat System. This three part solution is geared to deal with finding remote controlled weapons that are designed to detonate radioactive contents with a discharge that may or may not reach nuclear yield. Dirty bombs of this type are designed to cause terror and maximum panic.
-
Product
Electrostatic Discharge Generator
-
Beijing KeHuan Century EMC Technology Co,.LTD
Electrostatic discharge generator
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
Electrical Safety Test Solutions
-
Hipot Analyzers with 500VA output rating can be used to test and analyze the withstand voltage of high power and leakage current for the products like motor stators and rotors with high parasitic capacitance. Corona detection can be used for turn-to-turn or turn-to-ground test to avoid winding insulation failure from corona discharge.
-
Product
Regenerative Battery Pack Test System
17040
-
Chroma Systems Solutions, Inc.
The 17040 Regenerative Battery Pack Test System is a high precision system specifically designed for secondary battery module and battery pack test. It has an energy regenerative function to greatly reduce power consumption during discharge, and ensure a stable power grid without generating harmonic pollution on other devices – even in dynamic charge and discharge conditions. It is capable of recycling the energy discharged by the battery pack test back to the grid reducing wasted energy that traditional equipment discharges in the form of heat.
-
Product
Digital Insulation Resistance Tester (CE)
MIS-D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*The big digital and bar graph LCD display with back light enabled easy observation. Especially useful when working in dark place.*Hand free and continuous measurements with custom made switch.*Safe design with built in automatic discharging function for any capacitors present in the circuit.*The voltage in the circuit or capacitor can be checked by warning lamp for safe insulation measurements.*Data hold and auto power off function.*Compact, light weight and heavy duty rugged case.
-
Product
Electrostatic Discharge Testing
-
MET Labs offers special ESD testing services at controlled temperature and humidity, in a specially-designed and dedicated chamber.The chamber consists of ESD waveform verification setup and tables that accommodate a variety of EUTs. The chamber has a capability to vary the relative humidity from 15% to 65% and temperature from 18°C to 24°C.
-
Product
PCIe Digital I/O Board, 16 Optically Isolated I/O Channels, 24V
APCIE-1516
-
8 digital inputs, 24 V, isolated15 interruptible inputs8 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Partial Discharge Tester
GTPD-2C
-
GTPD-2C Digital partial discharge tester is the digital partial discharge measuring and analyzer adopting the complete new generation technology. It is suitable for partial discharge detection in manufacturing factory and field handover test of transformers, generators, CT/PT, bushings, GIS, capacitors, power cables, switches and other high-voltage electrical equipment with various voltage levels and capacities.
-
Product
48V / 250 Amp Load
BD15-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
Product
Nexis GC-2030 BIDUFRGA
UFRGA Series
-
The Ultrafast RGA system utilizes the new Barrier Discharge Ionization Detector (BID) technology coupled with Nexis GC-2030 to create new system GC for ultrafast, high-sensitivity analysis. Since the electrode creating Helium plasma is totally isolated from the carrier gas, there is no chance to contaminate this electrode with a dirty sample. This enables long-term stability.
-
Product
Advanced Handheld Partial Discharge Detector
PDetector
-
Power Monitoring and Diagnostic Technology Ltd.
The PDetector is an ideal device for On-Line Partial Discharge (OLPD) testing of MV and HV equipment which employs all 5 types of OLPD sensor technology: Ultra-High Frequency (UHF), Acoustic Emissions (AE), Ultrasonic, High Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV). The information from multiple sensors gives the PDetector the versatility to detect all types of PD in all types of substation apparatus. The exact type of PD activity can be determined effectively using multiple on-screen data spectrum analysis.
