Discharge
-
Product
Battery Discharge Test Unit
125V DC 100A
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
Electrostatic Discharges
ESD3000
-
ESD3000 is the only ESD generator in the market using standard AA batteries to offer full flexibility to the user to replace them when needed.
-
Product
48V / 200 Amp Load
BD12-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Electrical discharge detector
-
SKF Condition Monitoring Center
Detect electrical discharges in electric motor bearings
-
Product
Capacitive Discharge Testers
-
For IEC Testing of residual voltage after plug disconnect. The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results. Scope output for viewing decay waveform. Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335. Recommendations for Pluggable Type B equipment. NIST calibration supplied; A2LA calibration available. 16A option for testing large equipment.
-
Product
High-concentration, High Flow Ozone Generator
SEMOZON® AX8407
-
The SEMOZON AX8407 generator converts pure oxygen into ozone through silent electrical discharge and achieves high output and high concentration level. It requires only minute levels of dopant nitrogen gas, far below the levels required for competitive ozone generators. As a result, the presence of contaminants, e.g. NOx compounds, is extremely low.
-
Product
Battery Testing
BTS 200
-
This testing and maintaining battery system allows to perform measurement of battery voltage, discharging current test and testing of battery capacity. BTS 200 can be connected with external load unit ELU 200.
-
Product
Load Banks
-
The only way to be certain that your stationary batteries will perform to specification is to test the batteries’ capacity with a DC load bank / portable battery discharge tester.
-
Product
Transmission Line Pulse Testing
-
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
Product
Battery Capacity Tester
BLU-A Series
-
The battery capacity test is performed to determine the health of a battery. DV Power’s battery load unit BLU-A is a portable, powerful, and lightweight solution for battery capacity measurement. It is applicable to any battery string such as lead-acid, Li-Ion, Ni-Cd, etc., with up to 500 V battery voltage. As a special feature, BLU100L model enables the capacity testing of a single Li-Ion cell.The capacity test is performed in an accurate and user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.Battery load unit BLU-A enables setting discharge currents up to 240 A, with a resolution 0,1 A. Furthermore, if higher currents are required, BLU-A units can be connected in parallel, or additional BXL load units can be used.The instrument offers the best power-to-weight ratio in the market. BLU-A models start from 12,8 kg / 28.2 lbs and deliver up to 28,4 kW of power.The user can select three discharge modes:Constant current,Constant power,Constant resistance.Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.The instrument monitors discharge parameters in real-time during the capacity test. A 4,3-inch touch screen display shows battery voltage, current, elapsed time, and capacity during the entire test. Also, BLU battery load unit can be used with DV-B Win software. As a result of that, a user can see a detailed numerical and graphical presentation of key parameters and can create reports in various formats.Testing with BLU-A doesn’t require a disconnection of the battery from the testing equipment.
-
Product
Conventional Power Supply Design with Simple Analog Controls
VLF Series
-
VLF hipots perform voltage withstand tests and provide the voltage source for diagnostic cable testing. There is no better method for verifying the AC integrity of a cable than applying VLF AC voltage. Tan delta and partial discharge measurement accessories are frequently purchased along with VLF equipment to extend their capabilities.
-
Product
Spectrometer - OSA
-
HighFinesse optical spectrometers LSA and HDSA are designed to analyse the multi-line or broadband spectrum of (un-)known light sources like cw and pulsed lasers, gas discharge lamps, super luminescence diodes, semiconductor laser diodes and LEDs. They are suitable to analyze the spectrum of telecom signals, resolve Fabry-Perot modes of a gain chip, and produce a spectral measurement of gas absorption.
-
Product
Battery Capacity Tester
BLU-T Series
-
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conducted in an accurate, user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU-T battery load bank enables setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, the BLU-T units can be connected in parallel, or BXL-T additional load units can be linked.The instrument offers a high power-to-weight ratio. BLU-T series has models starting from 12,8 kg / 28.2 lbs and up to 19,2 kW of power.A user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Discharge parameters can be monitored in real-time during the capacity test. A 4,3-inch touch screen shows overall battery voltage, discharge current, discharge test time and capacity during the entire test. Also, the capacity tester is compatible with DV-B Win software. A user can view a detailed numerical and graphical presentation of key parameters, and create reports in various formats.Testing can be carried out without disconnecting the battery from the service.
-
Product
Online Partial Discharge Alarm System
PD Annunciator™
-
The PD Annunciator™ unique design consists of a three channels acquisition module paired with sensors of your choice, most commonly TEV and Acoustic or HFCT. With many advancements and innovations, the PD Annunciator™ handles partial discharge monitoring on metallic cabinets using our proven and advanced technologies.
-
Product
Cable Discharge Solutions
-
Cable Discharge Event, or CDE, is an electrostatic discharge event that occurs when a cable is connecting to a piece of equipment with different potential. It occurs because there is a potential differential between the charge on a cable to be connected and the equipment. It doesn't matter if the cable is charged or if the equipment is charged. It's the potential differential that causes the discharge. ESDEMC develops commercial system for CDE reliability test and evaluation.
-
Product
Three-Pole Lighting And Surge Arrestor
PIVM12,5-275/3+0 Vseries
-
PIVM12,5-275/3+0 Vseries is a three-pole lightning and surge arrester Type 1+2 according to EN 61643-11 and IEC 61643-11. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305), where they provide the equipotential bonding and discharge of both, the lightning current and the switching surge, which are generated in power supply systems entering the building. The use of the lightning current arresters PIVM12,5-275/3+0 Vseries is mainly in the power supply lines, which are operated as TN-C system. The main use of PIVM12,5-275/3+0 Vseries arrester is in structures of LPL III – IV according to EN 62305 ed.2. The marking M specifies a type of construction with removable module.
-
Product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
Product
HDDH-3932 Single Cell Battery Activator
-
HD Power Test Equipment Co.ltd
HDDH-3932 Cell Activator is used to discharge and charge and activate for disable single cell battery, which is simple, safe and accurate test device.The instrument is with perfect protection function, sound and light alarm and clear interface tips.
-
Product
Partial Discharge Detection Calibration Device
-
Hangzhou Xihu Electronic Institute
Calibration Device of Transient Earth Voltage PD detector, calibration device of ultrasonic PD detector, calibration device of high frequency PD detector, calibration device of ultra high frequency PD detector.
-
Product
Shielded Rooms
-
HIGHVOLT Prüftechnik Dresden GmbH
Electromagetic field and line-conducted interference needs to be eliminated in order to measure low-intensity partial discharges with a PD background noise level (≤ 1 pC) in accordance with IEC 60270.
-
Product
48V / 250 Amp Load
BD15-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
Product
High Voltage Discharge Rod
DSR-50K & DSR-100K
-
Standard Electric Works Co., Ltd
● For discharging and earthing for cables ● For discharging and earthing of test units● For safety purpose
-
Product
Multi-Cluster Sources
-
Our complete line of sources can be configured in a Tri-Source configuration. Clustered sources are a vital part of effective seismic exploration. The destructive effects of the air blast associated with a discharging air source are made worse by clustering. In order to maintain the separation between air sources within a cluster, it is necessary to mechanically constrain the sources with rigid bars.
-
Product
Battery Charger/Discharger
BCD-3932T
-
Kongter Test & Measurement Co., Limited
This battery charger/discharger/regenerator is compact unit for regular maintenance of single cell, especially for old cell. It plays three roles for complete solutions: charger, discharger and activator, which will facilitate your maintenance for batteries.
-
Product
Portable Strain Gage Welding and Soldering Unit
700
-
A battery-operated capacitive discharge spot welder for attaching and wiring weldable strain gages and temperature sensors.
-
Product
Horn Antenna
-
Horn antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in electric assets like GIS and GIL or MV and HV power transformers. It is a broadband antenna with a flat response which makes Horn antenna suitable in a number of different applications. It has been optimized to operate in a frequency range suitable for PD activity monitoring and it was designed to provide maximum sensitivity and high gain.
-
Product
Four-Pole Metal Oxid Varistor Surge Arrestor
PIIIM-275/3+1 Vseries
-
PIIIM-275/3+1 Vseries is a four-pole, metal oxid varistor surge arrester combined with gas discharge tube, Type 2 according to EN 61643-11 and IEC 61643-11. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 1-2 (according to IEC 1312-1 and EN 62305), where they provide the equipotential bonding and discharge of the switching overvoltage, which is generated in power supply systems entering the building. The main use of PIIIM-275/3+1 Vseries arrester is in all kinds of industry, residential and administration buildings. They are to be placed into the subsidiary switchboards or control boxes.
-
Product
Lead Acid Intelligent Battery Tester
612
-
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
Product
Reference Radiators / Comb Generators
-
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
