Discharge
-
Product
DC Load Simulating Inductors
-
Osborne has developed a wide range of DC load simulation inductors that are known for the transients they produce. Osborne DC load simulation inductors are unique and innovative because they are engineered to produce a precise time constant current transient during the current charge cycle.Another distinguishing feature of our load simulation inductors is that they produce a precise voltage transient during the current discharge cycle. The resulting test circuit can be used to accurately replace real loads in a variety of circuit simulation applications.
-
Product
Solar power Controller
-
The controller computer chip on the battery voltage, solar battery voltage, discharge current, ambient temperature and other parameters of sampling, through a dedicated control chip basis, the realization of the battery discharge rate and temperature compensation for high accuracy control of the amendment, and intelligent and efficient use of pulse-width modulation (PWM) charging vague way to recharge batteries to ensure the batteries work in the best condition, significantly extended battery life.
-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
Battery Fuel Gauge
-
Global Digital Instruments, LLC
SenDEC Battery Fuel Gauges are designed to accurately monitor the charge capacity of lead acid batteries. SenDEC fuel gauges can be used to monitor DC powered equipment such as fork lifts, golf carts, floor care equipment, and any other battery powered equipment. Three battery discharge profiles are standard, plus custom profiles, and a lockout option.
-
Product
Battery Test Systems
-
The Intepro’s battery test systems are configurable systems designed to test the latest Lithium Ion batteries and other high power density batteries and chargers. Combining high resolution, high powered charge and discharge systems, Intepro IBT line of battery test systems link to the battery management through the bus communication and fail-safe external monitoring of key battery parameters.
-
Product
ESD - Simulator
SESD 230
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
Handheld PD Tester
-
Weshine Electric Manufacturing Co., Ltd
TEV partial discharge inspection instrument uses two emerging technologies, transient-to-ground voltage (TEV) measurement and ultrasonic (US) measurement, to detect faults in switchgear. The equipment is portable and easy to operate. The TEV sensor is attached to the wall of the box, and the US sensor scans and detects along the gap on the switch cabinet.
-
Product
Lithium battery 128kWh Lifepo4 Battery pack 280Ah with BMS for Solar Energy Storage System
SPVLI-128kWh
-
Zhejiang Sandi Electric Co., Ltd
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
-
Product
Dielectric Loss Tangent Testing Instruments
-
Insulation materials in electrical equipment are used between a pair of electrodes; therefore it can be expressed as capacitors. Applying AC voltage to a capacitor with insulation materials causes an energy loss due to the leak current, the dielectric polarization, and the partial discharge. Because of this, the phase of the capacitor current is more delayed than that of a zero-loss current (reactive current) flowing in an ideal insulation material. The delay angle is called "Dielectric Loss Angle", and the tangent is "Dielectric Loss Tangent" (tanδ). Please refer to the technical guide explained in detail.
-
Product
Load Modules
-
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
Product
SMART Constant Current DC Load Banks
SLB-Series
-
SMART Constant Current DC Load Banks are designed for acceptance testing, discharge testing, battery capacity testing, battery maintenance, engineering examination and other testing for DC power with load. The SMART technology allows a constant current discharge without the need for manual adjustment of current during the discharge test. Our SLB-Series load banks are portable, durable, economic, safe, easy-to-use and come complete with our DataView software, providing the user with a complete data management and analysis program.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
Regenerative Battery Pack Test System
17020
Test System
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced by the battery module ei ther back to the channel s in the sys tem performing a charging function or to the utility mains in the most energy efficient manner. This feature saves electricity, reduces the facilities thermal foot print and provides a green solution by reducing the environmental impact on our planet. Chroma's 17020 system is equipped with multiple independent channels to support dedicated charge / discharge tests, on multiple battery modules / packs, each with discrete test characteristics. The channels can easily be paralleled to support higher current requirements. This feature provides the ultimate flexibility between high channel count and high current testing.
-
Product
Capacitor to Dampen
DAM2
-
Lifasa - International Capacitors, SA
DAM switching capacitors are used to protect semiconductors (IGBT transistors). These are charged and discharged repeatedly with high current peaks.
-
Product
Cable Diagnostic Tools
-
For non-destructive diagnostic testing to determine the quality of a cable’s insulation with minimal risk of failure, HVI recommends tan delta and partial discharge testing for valuable diagnostic data about cable insulation integrity. Both use a VLF source to perform elevated voltage, off-line testing. Tan delta testing measures insulation health, while PD identifies specific problem areas and assesses their severity.
-
Product
Battery Cycler
-
Rechargeable (secondary) batteries in real-world applications are charged and discharged many times until they reach end of life. Examples of this are batteries used in cell phones, PCs, power tools and automotive applications. After multiple charge/discharge cycles, cell performance starts to degrade. The batteries typically require charging more frequently until eventually they reach end of life and need to be replaced, with the original cells either being scrapped or repurposed.
-
Product
High Voltage Film Capacitors (Axial Leads)
STVHF/STVHE-A
-
For High Pulse / High Energy Discharge applications with low discharge repetition rate, please tell more about your application. We might have a suggestion.
-
Product
Electro Field Meter
-
Electrostatic discharge is now a problem in many workstations, as modern microelectronics (integrated devices) are susceptible to damage caused by electrostatic discharge. However, other industries, such as telecommunications, plastics and explosive industries, are also severely affected.
-
Product
Ultrasonic Leak Detector
ULD-410
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-410 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure.
-
Product
Battery Simulator
Battery Simulator
The battery simulator is used for testing satellite power supplies and is used in combination with a Solar Array Simulator and load systems (consumer simulation) for the validation and commissioning of satellite power supplies. Loads and power supplies in the battery simulator are operated in combination to represent a 2-square function and to simulate both charging and discharging of the battery.
-
Product
Battery Discharger & Capacity Tester
IDCE-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
Each wireless module can monitor 4 batteries simultaneously comparing with the traditional method that each module only canmonitor 1 battery, the new wiring operation become easier because the quantity of new modules needed is only a quarter of old-fashioned modules.
-
Product
Online Partial Discharge Monitor
ASM-E
-
The ASM-E is a permanent partial discharge monitor for cables, switchgear and other high voltage assets.The ASM-E can be configured with up to 128 PD sensor channels. If excessive discharge is detected, the ASM-E raises an alarm that can be configured either locally or by email/SMS. This enables the long-term assessment of plant conditions to be carried out quickly and easily, from any remote computer.
-
Product
RiverRay ADCP
-
Teledyne Marine RD Instruments
Go straight to work collecting highly accurate stream and river discharge data with the RiverRay Acoustic Doppler Current Profiler (ADCP).
-
Product
24V / 400 Amp Load
BD12-24P-12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 24V battery systems and is extremely cost effective.
-
Product
Intelligent Uninterruptible Power Supply Module With 24±20% VDC Input And 24 VDC Output
PPC-IPS-150
-
24VDC output, with auto shutdown function to PCWide Range power input for 24±20%VDCSupports over discharging protection to extend battery lifeWith free software utility for configuration and monitoringExecute auto shut down PC by App timing settingWith status LED indicators for monitoring battery pack and input powerWith changeable battery pack for easy maintenanceMetal enclosure supports VESA 75/100 and DIN Rail mounting
-
Product
Static Honest Meter
-
Sataton Instruments Technology CO., Ltd
Static honest meter is professional designed to determine the attenuation of static electricity, corona discharge time, static voltage attenuation half-life, static decay curve and other electric property of fiber, yarn, fabric, textile or plate materials. It is suitable for measuring the diffusibility of static in the testing samples.
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
Transformer Winding Resistance Meters
TWA Standard Series
-
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
Product
AC/DC Power Capacitors
ACF Series
-
For 70Vac~400Vac / 100Vdc~700Vdc Pulse Current requirement, please refer to our DC Pulse Current Capacitors for Power Electronic applications.For continuous and High RMS Current requirement, please refer to our High AC Current Capacitors LC series, which support continuous duty even at +105C.We manufacture AC Filter Capacitors for a wide variety of applications with different Capacitances, Voltages, Discharge Energy ranges, dv/dt, Pulse Discharge Currents, RMS Currents, frequency ranges, size restriction and even capacitor mountings.
-
Product
AC Test Transformer Products
-
Shanghai Guantu Technology Co., Ltd.
Manufacturing scope:Output voltage: 0~200kVOutput capacity: 0~20kVATechnical features of AC test transformer:Light weight; adopting oil-filled and air-filled structures reduces weight by 20% year-on-yearStatic noise; uniform electric field design and special fastening structure, no discharge and no mechanical noise at rated outputHorizontal iron core structure reduces the center of gravity of the equipment to a low pointMulti-flange combination with high structural strengthKey parts are cushioned with advanced elastic materialThe control box has complete protection functions and strong overload capacity
