Showing results: 871 - 885 of 2623 items found.
-
National Technical Systems
Conductive Anodic Filament (CAF) testing helps to determine the reliability of a printed circuit board (PCB) laminate material or a finished product. With conductor spacing and overall part sizes getting smaller and smaller, the necessity for this test is increasing.
-
CCM1095 and CCM2096 -
Teledyne RF & Microwave
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.
-
LCI™ -
ndb Technologies Inc.
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
WR14 -
Raytech AG
Raytech's Digital Winding Resistance meter WR14 is the battery powered version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy measurement of very low resistance of any inductive loads.
-
ZET 7010 -
ZETLAB Company
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
FFR1000 -
Rhesca Co., Ltd.
This equipment is designed to bend a flexible printed circuit board, which has a high degree of freedom and versatility, and at that time, apply a load to the bending point at the initial stage or each time, and repeat bending and unfolding to confirm the durability.
-
WXU -
CKD Corporation
An integrated unit that integrates the flow sensor and valve of the circulation circuit of the cooling water.The complicated piping design around water and the number of man-hours for piping work are greatly reduced, and the footprint is reduced by 80% to save space in the system.
-
Mors Smitt Group
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
Carl E. Holmes Company
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
-
Desco Industries, Inc.
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
1934B -
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Detect faulty wiring in 3 wire receptacle.*Test for GFCI receptacle for proper operation, 110-125V circuits.*Various combinations of three lights tell if wiring is correct or six possible faulty conditions.
-
1934 -
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Detect faulty wiring in 3 wire receptacle.*Test for GFCI receptacle for proper operation, 110-125V circuits.*Various combinations of three lights tell if wiring is correct or six possible faulty conditions.
-
U1280 Series -
Keysight Technologies
The Keysight U1280 Series handheld digital multimeter (DMM) is a true RMS multimeter which provides an accurate and reliable measurement. You will enjoy 60,000-count display resolution and 0.025% basic DCV accuracy for troubleshooting electronic circuits.
-
B2962B -
Keysight Technologies
The Keysight B2961B Series 6.5-digit low noise source power supplies provide a power supply and source solution that meets the difficult measurement challenges researchers, designers, and developers face working on advanced components, circuits, and materials.
-
111EXT3122-12XX -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.