Showing results: 1096 - 1110 of 2618 items found.
-
Keysight Technologies
Shorten design cycles to achieve first-pass design success. Our next-generation integrated electronic design automation (EDA) software provides engineers with new tools and enhancements to bring efficiencies into their printed circuit board (PCB), RF and microwave, 5G / 6G, and high-speed digital design flows.
-
800 Series ATE -
Circuit Check, Inc.
The Circuit Check 800 Series ATE provides the versatility of utilizing the economical drop-in fixturing present in the 600 Series or an integrated dedicated fixture, while simultaneously providing the increased test equipment capacity of the 1000 Series. This combination produces a cost effective full turnkey test solution.
-
PCAN MicroMod FD Evaluation Board -
PEAK-System Technik GmbH
The PCAN-MicroMod FD Evaluation Board is a development board for the PCAN-MicroMod FD and enables the design and development of your own circuits with CAN connection and I/O functionality. It can also be used for training purposes for CAN and CAN FD structures. The user can access the resources of the attached PCAN-MicroMod FD via taps, screw terminals, switches and potentiometers and test configurations or test circuits.
-
767943 -
Wesbar
Plug these testers into any car connector and you will have an instant test of running light circuits. Features LED display to show completed circuit for the running lights left turn signal and right turn signal. Auxiliary and electric brake circuit are included on the 6-way tester and auxiliary, electric brake and battery charge are included with the 7-way tester. One piece units with internal ground. Proper installation and set-up of a brake control, when a trailer is not readily available, is possible with the 7-way tester. Current Monitor testing device is designed to assist in determining whether a tow vehicle's 7-way blade car end connector has been wired properly. (Current Monitor is an excellent diagnostic tool for installation, setup and troubleshooting of electric trailer brake controls.) The Trailer Tester is designed to help you quickly identify problems in the wiring of the trailer. This is done by testing the Left Turn, Right Turn, Tail/Marker, Brake and Back Up circuits on the trailer. The tester indicates approximate amount of current in each circuit (i.e. trailer battery). Brake Control Bench Tester is a test device designed to determine if a brake control is working properly. Checks brake control output, independent of vehicle wiring. Simulates many fault conditions including open ground, short circuit, open load and more.
-
Mounting On Circuit Board Or DIN Rail -
INELTA Sensorsysteme GmbH & Co. KG
*PCB mounting*Suitable as: setpoint device or rotary actuator*Compact in design* Robust aluminium housing* Gear safety clutch
-
85010120 -
Interpower Corp.
This International Socket Strip includes seven international test sockets. Input power is provided by a single cord terminated with a Continental European plug. For 220-240VAC Circuits: Continental Europe (CEE 7) Denmark Italy India (old British BS 546) Switzerland Australia/New Zealand United Kingdom/Ireland
-
260-6XLM -
Simpson Electric Company
Designed for the special needs of solid-state circuitry measurements, the 260-6XLM has extra low power ohms ranges. It also offers all of the advantages of the standard 260 family, including a resettable overload protection circuit on the 260-6XLPM. Both versions come with batteries, manual and test leads with alligator clips.
-
PMICs -
Renesas Electronics Corp.
Renesas' power management ICs (PMICs) are integrated circuits that perform various functions related to power requirements of a host system. A PMIC may have a combination of the following functions: DC to DC conversion, battery charging, linear regulation, power sequencing and other miscellaneous system power functions.
-
SC-2440 -
Kaman Fuzing & Precision Products
* Self-contained electronics* Built-in temperature sensor* Fixed gain output* Reverse polarity and short circuit protection* No calibration required* Low cost* Excellent performance with ferrous targets* Variable voltage input from 15 to 30 volts DC* Compact and rugged, IP-67* Extremely low hysteresis
-
TE3000-series -
LBA Group, Inc
The TE3000-series of RF vector network analyzers have full vector measurement capability, and accurately resolves the resistive, capacitive and inductive components of a load. The user can display the vector impedance plus a range of related parameters including SWR, reflection coefficient, return loss and R-L-C equivalent circuit.
-
IWATSU Electronic Co., Ltd.
Precise and accurate core loss measurementIwatsu's B-H analyzers which hiring CROSS-POWER method (IEC62044-3)enable precise and highly accurate measurement embedded minimized phase error integration on frequency spectrum with current detecting resisters and compensation on detecting circuit with full compensation on amplitude and phase characteristics.
-
S-Probe -
PacketMicro Inc.
S-Probe series of single-ended probes can perform up to 20 GHz are designed for RF, power integrity, and signal integrity testing. Its strong beryllium copper (BeCu) tips is perfect for direct probing of uneven surfaces, such as solder pads and circuit components. This is a big improvement over the fragile microprobes.
-
BS407 -
Aim-TTi
High basic accuracy of 0.1%Wide range of 1 µΩ to 20 kΩCurrent reversal switch for detecting thermal EMF effectsCurrent diversion switch for easy zeroingFour terminal measurement using Kelvin clip leads (supplied)Battery operation with built-in charger20mV clamp for "dry circuit" testing
-
ChenYang Technologies GmbH & Co. KG
is a sophisticated Hall Effect Gear Tooth IC featuring an on-chip 12-bit A/DConverter and logic that acts as a digital sample and hold circuit. A separate 6-bit D/A converterprovides a fixed hysteresis. The sensor does not have a chopper delay. It uses a single Hall platewhich is immune to rotary alignment problems.
-
Renesas Electronics Corp.
High-speed CMOS output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a CMOS output IC on the output side. This coupler is a high common mode transient immunity (CMR), high-speed CMOS output type device designed for high-speed logic interface circuits.