DAQ Systems
Sense, log and store information.
-
Product
Hall Effect Measurement system
HMS-3000
-
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Product
Blackbody System
IR-564/301
-
Infrared Systems Development Corp.
The IR-564 extends the temperature range of the IR-563 to 1200 º C by changing cavity materials to Silicon Carbide and high purity Alumina ceramics, otherwise the two units are virtually identical.
-
Product
DC Parametric Test System with Curve Trace
DC3
-
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
Product
FTIR Compact & Portable Systems
-
To meet the challenge of FTIR analysis in the field, Agilent has developed the world's smallest FTIR instruments. Our compact FTIR systems deliver the sensitivity and efficiency of a lab-based system, yet are fully portable. These portable FTIR systems feature integrated power supplies and our Flexscan and Exoscan technology for efficient scanning performance. Lightweight handheld FTIR optics and sampling modules enable advanced FTIR capabilities in field applications such as conservation and mineral identification.
-
Product
VLF Testing and Diagnostics System
PHG 70 TD/PD
-
Cable testing and diagnostics with the BAUR PHG 70 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate * individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltageCompact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
ThermalAir Desktop Series Temperature Forcing System
ThermalAir TA-1000A Desktop System
-
The ThermalAir TA-1000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
Product
Automated System for DMA+ Series
Xpander
-
METRAVIB Xpander is a unique cost-effective solution to address the increasing throughput requirement of testing laboratories. Xpander is an automated specimen handling system dedicated to the DMA+ series Dynamic Mechanical Analyzers.
-
Product
Walking Test System Kit
PGA-710
-
The PGA-710 Walking Test System is a complete kit designed to perform the walking test per ANSI/ESD STM97.2 and IEC 61340-4-5. The system consist of several devices designed for portability and to perform several different tests which includes measuring the voltage on a person in combination with floor materials and footwear.The kit includes the PGA-710B Data Logger, the PFM-711B Field Meter, CPM-720B Charge Plate Monitor, the PCS-730B Electrostatic Charger, Hand Held Electrode and the Prostat Autoanalysis Software version 2.0.
-
Product
Automated Potentiometer Systems
-
Measurements International Ltd.
Intrinsically Accurate Self-Calibrating Ratio Divider, Best Accuracy < 0.05 ppm, Built-in 20-Channel Scanner, Arbitrary Voltages from 1 mV to 1200 V, Bipolar Voltage Measurements, Calibration of Fluke 5700A/5720A, Calibration of 3458A and 8508A, Calibration of Voltage Ratio Dividers (F752A, MI 1340A, G7520), Linearity Calibration of Digital Volt Meters (DVM), Traceability to 10 V Zener Reference.
-
Product
Refurbished Systems
-
Refurbishing ‘classic’ PAS 5500 and TWINSCAN lithography systems for a new life and a new purpose
-
Product
High Voltage Test & Measurement System
-
Hard-wearing and technically-sound High Voltage Test & Measurement System is developed to provide accurate results. These systems are widely used in power, electrical, engineering and other industries. They are designed using heavy-duty spare-parts to add strength with life to the systems. They are ideal to provide accurate results without any flaw to ensure to provide the best performance. These systems are perfect combination of easy usage, durability and high accuracy in results.
-
Product
Automatic Electrical Protective Equipment Test Systems
CBC-50С (CBC-100C)
-
Automatic systems CBC-C-series are designed for high-voltage withstand testing of electrical protective equipment and insulated hand tools. The tests are carried out with AC voltage (CBC-50C: UAC ≤ 50 kVRMS; CBC-100C: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
Product
Embedded MultiCore Systems
-
Sundance Multiprocessor Technology Ltd.
Boards and systems that aren’t connected through an internal PC bus.
-
Product
PXI based Test Systems Module
PXI XJLink2
-
The PXI XJLink2 module allows the integration of XJTAG into PXI-based test systems. PXI XJLink2 has one JTAG controller that can be connected to up to 4 JTAG chains, which are configurable for pinout and voltage. It is easily integrated with LabVIEWTM with a full set of Virtual Instruments (VIs) included.
-
Product
Thermal Imaging System for Electronics Testing
ETS320
-
Whether the goal is product testing or scientific research, heat can be an important indicator of how a system is functioning. The FLIR ETS320 is a non-contact thermal measurement system that pairs a high-sensitivity infrared camera with an integrated stand, for hands-free measurement of printed circuit boards and other small electronics.
-
Product
Eddy Current Test System
CIRCOGRAPH® Product Family
-
Foerster Instruments, Incorporated
The CIRCOGRAPH eddy current test system with rotating probes guarantees maximum detection sensitivity for exposed longitudinal surface defects on bright material. The test system is primarily used for wire drawing machines, Cu tube rewinders, and finishing sections in the bright steel sector. The individually tailored test systems by FOERSTER can be fitted with rotating sensors or CIRCOSCAN rotating discs. They scan flat and profiled material, e.g. when testing rails and billets.
-
Product
Entry Level GPR System for Concrete Inspection
StructureScan Mini LT
-
Geophysical Survey Systems, Inc.
The StructureScan™ Mini is GSSI’s all-in-one GPR system for concrete inspection. This handheld system locates rebar, conduits, post-tension cables, voids and can be used to determine concrete slab thickness in real-time.
-
Product
Controlled impedance test system
CITS900s4
-
CITS900s4 is the seventh generation of Impedance test system from polar, and typically the most popular model for customers who are new to impedance control. CITS900s4 provides both differential and single ended measurement capability along with 4 channels to provide flexible probe connection.
-
Product
Batteryless System Logger
SKU-004-01
-
The Batteryless System Logger is a unique device that was designed to log system data from any serial port, and store the data in the Logger’s non-volatile memory; this is done in the event of a system crash or power outage. The Logger is ideal for companies in the embedded appliance market.The System Logger connects to the embedded system via the serial RS-232 port. It continuously receives log info from the system, and stores this log info on an internal cycle buffer. This info can be retrieved via the serial interface at any time.
-
Product
Wafer Level Multi-Die Test System
ITC55WLMD
-
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
Product
3D Scanning System
CyberGage360
-
Unprecedented combination of speed, accuracy and one-button simplicity for non-contact automated 3D scanning inspection.CyberGage360 dramatically Speeds Up Quality Assurance of Incoming Parts Inspection & In-Process Inspection of components on the manufacturing floor; Lowers Cost of Quality & Speeds Up Product Time-to-Market. Designed for use in general purpose metrology, the CyberGage360 has a range of potential industrial applications from automotive to aerospace to consumer electronics, where high accuracy and high speed throughput are important.
-
Product
Environmental (Radiation) Monitoring System
Hawk® EMS
-
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
-
Product
True Phase Identification System
SPI-III™
-
Our vision has always been to create a phase identification system that exceeds any of today’s industry quality, safety and efficiency requirements. SPI-III’s unique design consists of a wireless bi-module combo that is stunningly easy to configure and operate. With many advancements and innovations, SPI-III will be more helpful than ever before, enabling field applications such as identification of A-B-C electrical phases from all 50 and 60 Hz networks, switchgear phase concordance (matching), phase rotation, system paralleling, underground phasing applications and more.
-
Product
Universal Testing Systems (Up To 300 KN)
3400 Series
-
Instron’s 3400 Series universal testing machines offer dependable performance across a broad spectrum of mechanical testing applications, with force capacities ranging up to 300 kN. These systems are well-suited for basic tensile, compression, flexural, peel, puncture, friction, and shear testing, and can be easily configured using a wide selection of grips and fixtures from Instron’s accessory catalog. Built with user safety and efficiency in mind, each system incorporates Instron’s proprietary Operator Protect technology, ensuring a secure and intuitive testing environment.
-
Product
Optics Test Systems
Front Window Scanner For Wedge Angle Measurement
-
Optik Elektronik Gerätetechnik GmbH
Scanning of complete automotive windshields to measure the wedge angle and thickness change, especially in the HUD area.
-
Product
High-Speed Digitizers and Multichannel DAQ Solutions
-
With our high-speed digitizers, we improve your measurement fidelity, signal integrity and measurement throughput, keeping low the total cost of ownership. The entire range includes PCIe, PXIe and AXIe form factors, configurable in single to multichannel solutions. Our products cover several applications in commercial OEM, aerospace & defense, wireless & RF communication and high-energy physics.
-
Product
Carrier with System Management
EnsembleSeries™ CCM3012
-
*PCIe Gen-3 interfaces to OpenVPX data plane*Advanced system management built-in (VITA 46.11)*Air, conduction, Air and Liquid Flow-By packages*Interoperable with other Ensemble OpenVPX processing modules*Fully MultiCore Plus® compatible
-
Product
Portable XRD System
TERRA
-
The TERRA Mobile XRD System, a high performing, completely contained, battery operated, closed-beam portable XRD, provides full phase ID of major, minor and trace components with a qualitative XRF scan of elements Ca - U. Its unique, minimal sample prep technique and sample chamber allow for fast, in-field analysis.
