DAQ Systems
Sense, log and store information.
-
Product
Environmental Radiation Monitoring Systems
-
With the autonomous radiation monitoring probe GammaTRACER, the gamma radiation dose is continually registered in the chosen time sequence. Energy-saving chip technology allows maintenance-free non-stop operation of the GammaTRACER probe of typically five years, with extended battery pack up to ten years! Hermetically sealed, it is designed to endure the harshest environments.
-
Product
Automated Optical Inspection System
AOI Series
-
Perform visual inspections of printed circuit boards (PCB) during manufacturing in which a camera is used to scan the board in extremely fine detail to check for any defects or failures.
-
Product
Vibration Test Systems
G-5 Series
-
Both Shock tests at from relatively high acceleration(max. 4900m/s2 -500G) to low acceleration with wide pulse width, difficult to achieve with conventional Shock Test Systems and Vibration tests for not only IEC, MIL and JIS but also requiring higher acceleration, velocity and displacement than ordinary VTSs can be carried out with one system.
-
-
Product
CRPA Test System
-
The Spirent CRPA Test System is a development of Spirent’s GSS9000 Series platform for testing Controlled Reception Pattern Antenna (CRPA) systems with a separate RF output per antenna element. The CRPA Test System generates both GNSS and interference signals. Users can control multiple antenna elements. Null-steering and space/time adaptive CRPA testing are both supported by this comprehensive wavefront approach.
-
Product
In System Programmers
-
In-circuit serial programming, also known as in-system programming (ISP) or in-circuit programming (ICP) enables programming and reprogramming of microcontrollers, serial EEPROMs and flash memories already soldered on a target PCB.
-
Product
Mill & Silo Monitoring System
MSM-100
-
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.
-
Product
Fiber Optic Sensor Systems
-
Fraunhofer Institute for Telecommunications
Fiber-optic and photonic measuring systems open up innovative measuring and control technology concepts for a wide variety of applications. They play a major role in optimizing energy efficiency and are important technological innovation drivers for new and future-oriented markets.In the Department of Fiber Optic Sensor Systems of the Fraunhofer Heinrich Hertz Institute, the focus of application-oriented research is on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication capability as well as extremely low power consumption or even a self-sufficient power supply.In the Department of Fiber Optic Sensor Systems at the Fraunhofer Heinrich Hertz Institute is focused applied research on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication skills as well as an extremely low power consumption, or even a self-sufficient energy supply.
-
Product
DC SQUID System
-
Quantum Design's patented high-symmetry SQUID design and electronics provide the most rugged and sensitive all-thin-film sensors commercially available, and give you everything you need to configure flexible, powerful detection systems for your research. These sensors can easily withstand the rigors of a laboratory environment such as repeated temperature cycling. Their robust performance offers a level of reliability and adaptability that has earned QD a worldwide reputation as the SQUID of choice. OEM services are also available for special commercial applications.
-
Product
Functional Test Systems
-
With extensive experience in functional test equipment, a world-wide service and support organization, and a broad range of software/hardware options, we will supply cost-effective production-ready test solutions to meet your test challenges. Proposals developed by our functional test engineering team include a detailed description of system requirements, test instrumentation, estimated test cycle times (as applicable), footprint, and other key specifications.
-
Product
High Speed Camera Systems
MEMRECAM MX
-
The nac MEMRECAM MX is a robust, turnkey solution for multi-camera onboard and offboard automotive testing and occupant safety applications. Each system supports up to eight, tightly synchronized camera views, and integrates seamlessly with all current and legacy MEMRECAM imaging systems.
-
Product
Vapour Permeability Measurement System
-
Mass Spectrometer vapour permeability measurement system which works across every gas or group of gasses used in modern engineering. This is important as vapour permeability issues effect many performance and safety critical aspects across the engineering industries.
-
Product
Automated Inspection Systems
-
Our systems utilize phased array and eddy current array to inspect the full volume and surface of various products and profiles in many manufacturing industries, such as metal, aerospace, transportation, power generation, and oil & gas.
-
Product
DC Power Systems
-
Allow efficient distribution of your telecom and data center power utilizing these reliable, scalable and flexible DC power products.
-
Product
Ferroelectric Test System
RT66B
-
Radiant's Rt66B offers amazing performance at an affordable price. The Rt66B is a perfect entry level system for measuring Ferroelectrics. This system does include Radiant's famous Vision Data Management System which offers all the standard measurements of ferroelectrics including Hysteresis, Fatigue, Waveform, C/V, I/V, PUND and much more.
-
Product
Flexible Automatic Measuring System Release
FAMS-R5
-
FAMS-R5 uses the system with high-speed communication, FAMS High-Speed Link2, to share data with each unit.Sensors can be directly connected to the measurement unit in a laboratory.Simple wiring and highly accurate measurement can be achieved.By adding the MCU that can calculate the control model with MATLAB/Simulink, it also supports the simulation bench.
-
Product
In-fuse Vehicle Current Measurement System
Sens-X
-
Sens-X intelligent sensors offer a range of high dynamic range sensor hardware for the capture of specialist current measurements.
-
Product
Emergency Alternative EDFA system
-
Telecommunication systems are vitally important in our daily lives, even more so during the rescue and recovery processes upon natural disasters, such as the earthquake hitting the east-coast of Japan in 2011. The deadly earthquake rattled the nation coast before unleashing a deadly tsunami that swept away cars, homes and businesses as it touched land. The communication infrastructure was among the victims. Rapid rebuilding of the telecommunication system becomes an absolute priority.
-
Product
RF Bias Burn-In System
-
These systems deliver an unbeatable combination of advantages over a wide range of RF frequencies and power levels. The Automated Multi-Channel RF-Biased Burn-In Test System is a turnkey system that incorporates all of the capability needed for accelerated aging and parametric testing of RF semiconductor devices. Its powerful software elegantly supports data acquisition, storage, and presentation. Accel RF’s customers choose system features to meet their technical needs and capital budget. In addition to cost savings, use of Accel-RF’s solutions accelerate product time-to-market, saving many months of product development.
-
Product
Portable Data Recorder System
PDR
-
Our Portable Data Recorder (PDR) is a low cost, lightweight data acquisition platform for lead paint inspection. It allows the inspector to efficiently identify and record inspection parameters without limitations.PDR interfaces with the Report Generation Software (RGS), streamlining data entry and allowing the inspector to produce instant inspection reports.
-
Product
Semiconductor Metrology Systems
-
MTI Instruments'' semiconductor wafer metrology tools consist of a complete line of wafer measurement systems for virtually any material including Silicon wafer (Si), Gallium Arsenide wafer (GaAs), Germanium wafer (Ge) and Indium Phosphide wafer (InP). From manual to semi-automated wafer inspection systems, the Proforma line of wafer metrology inspection tools is ideal for wafer thickness, wafer bow, wafer warp, resistivity, site and global flatness measurement. Our proprietary push/pull capacitance probes provide outstanding accuracy throughout their large measurement range, allowing measurement of highly warped wafers and stacked wafers. MTII''s solar metrology tools include off line manual systems for wafer thickness and Total Thickness Variation (TTV), as well as, in-process measurement systems capable of measuring wafer thickness, TTV and wafer bow at the speed of 5 wafers/second.
-
Product
Analog Output DAQ Cards
-
Analog output cards are ideal for DAQ applications where multiple A/O channels are needed for voltage and current output.
-
Product
Automated Marking Quality Control System
Angara
-
The machine vision system ASKKM "Angara" is designed to detect and reject defects in the marking of labels, excise stamps, boxes, vials, ampoules, bottles, etc., which have visual manifestations in the field of permanent or variable printing. It is installed on a conveyor or mounted in a labeling machine. Labels are checked before being applied to the product or marking on the package.
-
Product
60 GHz Systems and Modules
-
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules and customer prototyping for system development. This 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development system makes it easy to design new products and applications in the emerging unlicensed millimeter wave ISM band.
-
Product
BMS Test System
6020
-
High Extensibility: for multi-string battery cell, 4 cells per channel, expandable from 1 to 16 cells per strings
-
Product
Universal Testing Systems
-
Instron universal testing systems are versatile, high-accuracy platforms (available in electromechanical and hydraulic variants) designed to perform a wide range of static mechanical tests, such as tension, compression, bend, peel, shear, puncture, and more, on virtually any material. They support force capacities from fractions of a newton up to thousands of kilonewtons, with precision load measurement, high data acquisition rates, and compatibility with thousands of accessories, including a wide range of extensometers, grips, fixturing, and automation solutions to meet demanding quality and throughput standards.
-
Product
Wireless Belt-Pack Instrument System
IS400
-
The IS400 Digital Hybrid Wireless system sets new standards for wireless guitar and bass. Flat frequency response, low distortion and compandor-free operation provides the closest thing to using a high-quality instrument cable. The system faithfully reproduces the lowest fundamental from a 5-string bass (low B) at 32Hz up to the very highest overtones and harmonics.
-
Product
Vision Systems
-
Our GEVA vision systems offer the performance and flexibility to inspect multiple parts, assemblies or surfaces at the same time. These systems are equipped with multi-core processors, high-speed camera ports and versatile I/O options to match your application and factory integration requirements.
-
Product
Automatic System
-
By combining with Hardness Tester, stage control is automated in indent/multi-pointmeasurement to reduce the dispersion caused by each operator. This system is very effective for large-scale rationalization and energy saving.
-
Product
ICP Microphone System
378A14
-
This model includes a 1/4" microphone cartridge, a mated preamplifier with TEDS, and system calibration.
