Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
THREE WAY BACK PRESSURE KIT
TU24APB
-
*Allows quicker and more accurate testing of exhaust blockages in catalytic converters, mufflers, etc*2-1/2" gauge features two multi-colored bands - idle and 2,500 RPM - with pressures shown in PSI and bar*Includes 6' of hose, enough length to test from driver's seat
-
Product
O/E Converter
TIA-950
-
The TIA-950 optical receiver is the optimum instrument for the laboratory or for field use. This optical receiver can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. This compact unit mounts directly on the BNC input of an oscilloscope.
-
Product
Synchro & Resolver Buffer Amplifiers
RPMA - SPMA
Amplifier
Computer Conversions Corporation
The SPMA/RPMA Series are low cost solid state synchro and resolver buffer amplifiers, isolators and format converters packaged in industry standard 2.6 x 3.1" modules for printed circuit card mount.
-
Product
DC Converter
-
Primary switched DC converter modules are used, among other things, to generate different (consumer) voltage levels from central DC voltages, also battery-supported.
-
Product
RH850 Family (Automotive only)
RH850/E1x
-
RH850/E1x microcontrollers are ideal for powertrain applications, with built-in hardware for knock control such as delta-sigma A/D converter, Digital Filter Engine (DFE), Advanced Timer Unit (ATU-IV), and Autonomous Pulse Adaptor (APA), and engine control such as fuel injection control.
-
Product
Noise Sources
WGNS
-
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
Product
Bresle Salt Meter
Elcometer 138
-
Incorporating a flat sensor, the Elcometer 138 Bresle Salt Meter measures the conductivity of a sample, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9.
-
Product
Air Temperature Sensors
-
Campbell Scientific offers a variety of sensors for measuring air temperature. The electrical signals transmitted from the sensors to our dataloggers can be converted to different units of measurement, including °C , °F, and °K. Our dataloggers are also capable of measuring most commercially available air temperature sensors.
-
Product
Wall Transformer, Converters & Chargers
-
PeakTech Prüf- und Messtechnik GmbH
An appliance for holding or inserting a charge of power.
-
Product
Interface Converter
ZET 7177
-
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
Product
Web Sensor
T7511
-
Web Sensor with relative humidity and temperature probe on the cable. Built-in atmospheric pressure sensor.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Converter Signal Amplifier – 4…20 mA – Wall Mounting
HD978TR5
-
Configurable converter signal amplifier with 4…20 mA (20…4mA).
-
Product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7226 CAL D
-
The 72-7226 CAL D from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
Product
Boundary Scan
PROGBSDL
-
PROGBSDL software converts a BSDL file for an unprogrammed PLD into a BSDL file with the same pin usage as the programmed PLD.
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Product
6 Channel Digital Receiver Module
DP-VME-5826
-
DP-VME-5826 is a VME64x Six Channel Digital IF Receiver module. It samples and down converts analog IF signals into the digital base band data.The digital base band I/O samples generated from these IF samples are pulse compressed. Down converted I/Q data is sent to the signal processor through 2 channels of 2.5 Gbps speed SFPDP link.The digital waveform generator block of digital receiver unit generates programmable polyphase coded digital pulse coded expander output.
-
Product
Programmable Multifrequency Clock Synthesizer - PMC
Model 7191
-
- Simultaneous synthesis of up to up to 5 different clocks- Eight SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 100 MHz- Four programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status via PCI bus interface
-
Product
PoE Injectors, Splitters and Extenders
-
Advantech's fiber & PoE converters, injectors, splitters, and extenders are designed to provide network operators support for Mega PoE IEEE 802.3BT
-
Product
DCDC
DP Series
-
The DP family is an economically priced high performance series of regulated DC/DC converters offering single and dual outputs. Features include MOSFET design operating at a switching frequency of 100Khz, continuous short circuit protection, LC input filter, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. These miniature converters maintain excellent regulation over varying line and load conditions (0.2% for line and 0.5% for load). They are packaged in an IC compatible 24 pin DIP configuration measuring 1.25” x 0.8” x 0.4” high.
-
Product
Range-Doppler Target Generators
ATG9100
-
The ATG-9100 is an example of a laboratory-quality instrument that will simulate complex target motion. Microwave signals from the speed camera enter the instrument through an integrated antenna which is then downconverted and digitized. Target simulation data is added to the digitized signal to provide range and Doppler information. The modified digital data is then converted back to an IF and upconverted to the original microwave frequency of the speed camera and radiated back through the antenna. Since the ATG-9100 can be phase-locked to an external 10 MHz reference standard, this instrument is suitable for use as a calibration standard for speed cameras.
-
Product
Temperature and Humidity Regulator
H3431-2
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
Reference Transmitter
81492A
Transmitter
Keysight's 81492A Reference Transmitter is designed to offer excellent eye quality for NRZ and PAM4 signals at baud-rates up to 56 Gbaud and can serve as universal single-mode E/O converter. In addition to the internal lasers at 1310 & 1550 nm, an external optical input for usage with tunable laser sources is available. It is fully integrated into Keysight’s Optical Receiver Stress Test solutions to address test requirements of IEEE 802.3 10,40,100 and 400GBASE optical standards.
-
Product
Differential Probe
DP-30K
-
*30KVp-p, High Voltage Model .*Input Impedance 81.6MΩ//1PF *x200, x2000 Attenuator, Easy to Convert.*Separating Design(Standard No.114205)*Convenient & Durable.
-
Product
DC/DC converter 5 W
20IMX7-03-8G
-
DC/DC converter 7 W from Bel Power Solutions | input ranges 8.4 - 36 VDC | output 3.3 V | operates in ambient temperature from -40 to +85 °C
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Informtest Converter
-
Informtest presents software for converting data into formats compatible with the Mera WinPOS and NI DIAdem data processing tools in Microsoft Excel.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 2 GHz, 4 Analog Channels
DSOS204A
Oscilloscope
2 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.5 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
Universal Band Decoder
Bandmaster IV
-
Using USB (RS232) or band data (BCD) information, the Bandmaster IV converts that frequency/band data to allow meaningful automated control of your station that incorporates Array Solutions / Hamation devices.
-
Product
Power Supply Units
-
converts mains AC to low-voltage regulated DC power for the internal components of a computer. Modern personal computers universally use switched-mode power supplies.
-
Product
12 A/D Channels (±1.25 to ±10.0 VDC FSR); 24-bit Sigma-Delta
AD1
-
Module AD1 features 12 channels with up to 24-bit Sigma-Delta A/D converters for each individual channel. The maximum programmable, expected full-scale range input for the AD1 module is ±1.25 to ±10 VDC and ±12.5 to ±100 VDC respectively. The A/D converters have programmable sample rates of up to 256 kHz.
