Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
High Speed Fiber-Optic Detectors
-
High speed fiber-optic detectors use special photodiodes with high speed electronic circuits to convert fast pulses in optical fibers to electrical signals for measurement. Unlike our optical receivers, these photodetectors do not include a transimpedance amplifier.
-
Product
12 A/D Channels (±25mA FSR); 24-bit Sigma-Delta
AD3
-
Module AD3 features 12 channels with up to 24-bit Sigma-Delta A/D converters for each individual channel. The maximum programmable, expected full-scale range input for the AD3 module is ±25 mA respectively. The A/D converters have programmable sample rates of up to 256 kHz.
-
Product
Wet Oxidation TOC Analyzer
TOC-VWP
-
Phosphoric acid and the oxidant (persulfate) are added to the sample, which is heated under UV illumination to convert the TC in the sample to carbon dioxide. This carbon dioxide flows with the carrier gas via the dehumidifier into the NDIR sample cell. The area of the carbon dioxide peak signal is measured and this peak area is converted to TC concentration using a pre-prepared calibration curve.
-
Product
16 Channel Dual Range Multievent QDC
V965
-
The Mod. V965 is a 1-unit wide VME 6U module housing 16 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance). For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section.
-
Product
SparkFun Transceiver Breakout
RS-485
-
This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
-
-
Product
USB-to-Serial Cable Converter
-
This cable is the solution for users who want to communicate with GE Multilin IEDs via PCs that have USB communication ports. Using this cable is quick and easy. Simply install the cable driver on your PC, plug in the cable and you are ready to communicate.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
PXI-7841, Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module
780337-01
Multifunction Reconfigurable I/O
Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7841 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
Quad ASI To IP Conversion Module
DTM-3224
-
The DTM-3224 is a highly-integrated and cost-effective OEM module for converting four ASI transport streams to IP. The next-generation architecture of this device has support for IPv6 and for IGMP v3, enabling source-specific multicast.
-
Product
Adaptors
-
Is a device that converts attributes of one electrical device or system to those of an otherwise incompatible device or system.
-
Product
Multi Channel A/D Converters
-
Analog Devices multiplexed channel precision A/D converters include one ADC and span 8-bit to 24-bit resolutions and throughputs from kSPS to 10 MSPS, while offering industry-leading performance in noise, linearity, and dynamic range. ADI offers a quick and easily deployed multichannel solution suited to your application’s diverse needs in speed, power, and size. Engineered to accommodate single-ended, differential, and pseudo differential inputs, our multiplexed converters offer the feature set needed for next-generation end systems.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Serial-to-Ethernet Converter
MultiNet
-
MultiNet is a communications module that provides GE Multilin serial ModBus IEDs with ModBus TCP/IP communications over Ethernet, allowing connection to fiber optic LAN and WAN network systems. MultiNet has the capability to connect up to 32 serial ModBus devices eliminating complex wiring and additional communications converters, and providing a streamlined and economical Ethernet hub.
-
Product
Portable Analog Instruments
-
Instrument transformer is a general term for voltage transformers and current transformers that are used with electrical instruments. The main purpose of instrument transformers is to extend the measurement range for electrical quantities (voltage, current, power, power factor) on large-current and high-voltage circuits. They serve to convert currents and voltages to levels that are suitable for measurement, and to insulate the instrument, etc. from high-voltage circuitry.
-
Product
OEM Module For Conversion Between IP And ASI
DTM-3200
-
The DTM-3200 converts IP to ASI, or ASI to IP. Integrate this compact module to extend the range of I/O standards supported by your product. Technical highlights include advanced IP-jitter filtering, ultra-low latency and zero-jitter IP transmission.
-
Product
Pressure Control Setup Using Pid Controller
ULP-26
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Pressure Control Setup comprises of Pressure tank fitted with pressure transmitter to measure the pressure. The pressure is controlled by a pneumatic control valve operated by a I to P converter. The whole system is mounted on a Table top Model with all necessary Piping. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Breakout - General Purpose USB to GPIO+SPI+I2C
FT232H
-
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
Product
OnyxFX FlexorSet 2-Ch. 3.0 GHz A/D, 2-Ch. 2.8 GHz D/A - PCIe
Model 7070-320
-
The FlexorTM Model 3320 is a multichannel, high-speed data converter FMC.It is suitable for connection to RF or IF ports of a communications or radar system. It includes two 3.0 GHz A/Ds, two 2.8 GHz D/As, programmable clocking and multiboard synchronization for support of larger high-channel count-systems.
-
Product
DC/DC Converter 2 W
REM2-1509S
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | output 9 V | operates in ambient temperature from -40 to +95 °C
-
Product
Coaxial
-
Adapters for converting banana jacks or single-conductor test instruments to coaxial configuration for added shielding protection.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
-
Product
DC/DC Converter 2 W
REM2-3.305S
-
DC/DC converter 2 W from Recom | input ranges 3 - 3.6 VDC | output 5 V | operates in ambient temperature from -40 to +95 °C
-
Product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
-
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
DC Electronic Load
63600 series
-
Chroma's 63600 series DC electronic loads are designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, server power supplies, and power electronic components. They are excellent for research, development, produc t ion, and incoming inspection applications. The 63600's state of the art design uses DSP technology to simulate non-linear loads using a unique CZ operation mode allowing realistic loading behavior. The 63600 series can draw its rated current under very low voltage (0.4V typical). This unique feature guarantees the best loading performance for modern Point-of-Load conditions and fuel cells.
-
Product
500 Watt DC/DC Converter, 3U VPX
VPX55H-3
DC Converter
The VPX55H-3 is NAI's latest high power 500 Watt DC/DC converter that accepts a +28 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 0.8” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
External Input Module
EIM-01
-
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
Product
DC/DC Converter 140 W
CTS-120-6875-D
-
DC/DC converter with 140 W from Premium | input ranges 43.2 - 90 VDC | output 24 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
HIL and RCP DFIG Laboratory
-
This laboratory combines the best of both OPAL-RT and Festo solutions to deliver academic researchers and teachers with the ideal Hardware-in-the-Loop (HIL) and Rapid Control Prototyping (RCP) simulation system to conduct experiments and teach in the fields of electrical machinery, power converters and wind energy generation.
