Showing results: 6151 - 6165 of 6945 items found.
-
LPCI-3488A -
ADLINK Technology Inc.
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
Finero OY
FST-500 High Voltage Cable Tester is a modular and customizable cable tester that can be easily adapted to various cable test or cable harness test applications. The electronics is based on Finero’s rugged industrial grade FST range of standard test equipment. All set and measured values are shown on alphanumeric display, additionally there is an analog panel meter for output voltage. Other cable paramerter like L, C and R can also be tested by using optional test and measurement equipment. The tester can be ordered with a build in PC and it can be used in conjunction with Finero’s Quality Control software.
-
Model FT1 -
Gopal Electronics
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
1500 -
Edgetech Instruments
The Model 1500 is a self contained system; not only is there no field assembly required, there’s no need to carry around a myriad of individual components such as control boxes, sensors, cables, pumps, and power cords. Simply attach the sample line, adjust the flow (with the integral flow meter) and turn on the power. Within minutes you’ll be collecting field dew point data with the same chilled mirror accuracy of a lab standard hygrometer. And with a nominal battery life of 12 hours, you will be able to collect for the entire shift or spot check your processes for several days.
-
40-736-001 -
Pickering Interfaces Ltd.
This Data Communications Multiplexer is designed specifically for multiplexing or de-multiplexing up to 32 differential signal pairs having controlled 100 differential impedance. The multiplexer can be configured under software control to provide switching for 32 differential pairs, 16 dual differential pairs and 8 quad differential pairs. The dual and quad versions are particular well suited for providing switching of AFDX, BroadR-Reach and Ethernet signals. To support Ethernet applications, the design includes a switching network that simplifies the swapping of Tx and Rx pairs to simulate the effect of Ethernet crossover cables.
-
36330 -
S & G Tool Aid Corp
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
YAVAR438 -
6TL Engineering
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Fortress Technology Inc.
Our revolutionary Halo system is an automatic metal detector testing device. It is designed to automatically test ferrous, non-ferrous and stainless steel samples on all Fortress metal detectors. Automatic testing saves time, money, labor, along with removing the risk of human error and work place injury at critical control points on a manufacturing line while complying with industry standards. The Halo system is ideal for applications where manual testing of a metal detector is made difficult due to access, position, access to the product flow, environmental conditions, etc.
-
190 -
Electronic Specialties Inc.
Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
784756-01 -
NI
8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis - The NI‑9145 is a rugged EtherCAT slave chassis for adding deterministic, distributed I/O to any CompactRIO, PXI, or industrial controller with two Ethernet ports. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. You can daisy chain multiple NI‑9145 slave chassis from the master controller to expand time-critical applications to higher channel counts while maintaining hard determinism with minimal processor resources.
-
GVS7116 -
CRYSOUND
GVS7116C Automatic sweep signal generator is an instrument designed for detecting various electroacoustic components (Rattle & Buzz) as well as for their dynamic tests. It is suitable for use in the R&D department, quality control department and production line of manufacturers of speakers, headphones, receivers, buzzers, and sirens, as well as for the inspection of incoming materials in factories that manufacture various electroacoustic products, such as audio factory, telephone factory, earphone factory, speaker factory, and computer multimedia factory, etc. With standard sine wave and low distortion, it is the most suitable for listening to noise from speakers.
-
Keysight Technologies
Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.
-
Cyth Systems, Inc
Automated Testing Engineering and Automated Test Equipment (ATE) provide a faster, more efficient way to test your product. With the help of LabVIEW and Modular Instruments, our engineers create test and measurement systems for all areas of product design and manufacturing.Whether you are in early stage R&D prototype testing, and design validation, or providing a solution for quality control and life testing our engineers can work with you to design fully customized automated Test Systems using entirely off-the-shelf products to ensure you deliver quality product on time.
-
CPX Series -
Aim-TTi
PowerFlex design gives variable voltage and current combinations within a maximum power rangeUp to 60 volts and up to 20 amps180 watts or 420 watts maximum per outputIsolated outputs can be wired in series or parallelConstant voltage or constant current operationSettings Locking (S-Lock)PowerFlex or fixed-range operationVariable OVP tripsSelectable remote sense terminalsCompact quarter or half rack 3U case sizeIsolated analogue remote control (CPX400SA only)RS232, USB & LXI compliant LAN (P models only)GPIB Option (P models only)
-
NI
PXI Digital Waveform Instruments feature up to 32 channels, can sample and generate digital waveforms at up to 200 MHz, and interface with various standard TTL and low-voltage differential signals (LVDS), as well as settable voltage levels. These devices offer per clock cycle, per channel bidirectional control, and phase shifting. They include deep onboard memory with triggering and pattern sequencing. Some models also support doubledatarate (DDR) technology and real-time hardware data comparison. You can use Digital Waveform Devices to create device simulation and complex stimulusresponse tests.
