-
product
High-End Rack Modulator/Exciter
VORTEX
VORTEX is a very innovative and advanced solution that supports ATSC 1.0 waveform on an optimized hardware platform.It has been especially designed to meet transmitter manufacturer’s demand for integrating a “read-to-use” and future proof modulator/exciter within their own designs.Fully controlled via a friendly WEB GUI and via SNMP, VORTEX features some very unique functionalities dedicated to control the transmitter (TX) such as a Power Measurement Unit (measuring in real-time the forward and reflected power levels), the TX power ON/OFF control system and the Automatic Gain Control (AGC) mechanism.VORTEX Digital Adaptive Precorrection circuits, powered by TeamCast GAP® – Green Adaptive
-
product
Control Devices
National Meter Industries Inc.
4-input impulse centralising equipment. Inputsare optoisolated to read impulses and it has a 32-bit memory to store the valuesmetered.
-
product
Electronic Engine Controls - FADEC
The EMC-100 is dual channel Full Authority Digital Engine Control (FADEC) system, designed for helicopter turboshaft engines. The electronic control unit’s (ECU) primary channel provides precise engine power management and rotor speed control throughout the operational range of the engine. The reversionary backup channel provides full mission capability should a primary system failure occur.
-
product
Radar Level Sensor
VRS-20
Versatile and simple to install, the VRS-20 has been developed by Valeport to work seamlessly with the TideMaster Tide Display/Logger and other third party data loggers using RS232, RS485 and SDI-12 communication. Non-contact technology removes the installation, corrosion & fouling issues of submerged sensors, while simplifying datum control. Accuracy and performance are unaffected by changes in water density and atmospheric conditions.
-
product
Astronics PXIe-1209 , 2-Channel, 100 MHz PXI Pulse Generator
785033-01
2-Channel, 100 MHz PXI Pulse Generator - The Astronics PXIe-1209 provides dual independent pulse generation with full control of all timing parameters with extremely high resolution. Both channels are fully independent, and you can configure pulse delay, double pulse spacing, pulse width, and period. Each channel offers front panel trigger inputs with software-programmable thresholds and PXI backplane triggering.
-
product
Power Electronics Test Bench
OP1300
The multi-purpose and ready-to-use Power Electronics Test Bench combines a state-of-the-art Hardware-in-the-Loop (HIL) simulator from OPAL-RT with Imperix’s Rapid Control Prototyping (RCP) system and real power hardware. It enables rapid development of power electronics, drives and smart-grid applications across industry and academia.
-
product
Stationary 1D Bar Code Readers
Leuze electronic GmbH + Co. KG
In production and logistics, the identification of goods and materials through universally usable 1D bar codes controls many processes. The areas of application of our readers are accordingly diverse – from miniature scanners to compact scanners and bar code readers with large reading distances for industrial application. Modular systems, pre-mounted for intralogistics or bar code scanners for specific industries, e.g., for laboratory automation, round out the areas of application. Scanning rates of up to 1,000 scans/s, small installation dimensions, robust housings and integrated heating for use in deep-freeze areas meet the individual requirements of your application.
-
product
Video Autofocus Option
Applied Scientific Instrumentation
ASI's video auto-focus provides a simple focus control solution when using an analog video camera and any of ASI's products with Focus Control including standard and piezo XYZ stage systems, linear and gantry stage systems, and stand-alone MFC-2000 focus controllers.
-
product
Precision DC Power Module, 20V, 50A, 500W
N6765A
The Keysight N6765A is a 500 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB and LXI compliance are standard. Select from more than 30 different DC power modules ranging in capability from basic to high precision, and in power from 20-500 Watts.
-
product
Modular DC Power Supply
62000B
Chroma Systems Solutions, Inc.
Chroma’s 62000B series of Modular DC Power Supplies offer 5 types of power module with ranging from 1V to 150V, current from 10A to 90A, and offers two mainframe type of six and three position. The six position mainframe can envelop in up to six power modules paralleled operation for 9KW power output. The 62000B can easily parallel up to 14 mainframes to 120KW with current sharing and CAN bus control for bulk power applications.
-
product
USB-7855, Kintex-7 70T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device
782915-01
Kintex-7 70T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7855 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7855...show more -
product
Power BI Embedded
Quickly and easily provide customer-facing reports, dashboards, and analytics in your own applications by using and branding Power BI as your own. Reduce developer resources by automating the monitoring, management, and deployment of analytics, while getting full control of Power BI features and intelligent analytics.
-
product
Solid State Power Amplifier System 32 - 40 GHz, 10W
AMP4052
Exodus Advanced Communications
AMP4052, 32-40GHz, 10W, 40dB, 100-240VAC system. This Class AB linear State of the Art Solid State Power Amplifier features an instantaneous wide-band GaAsFET design with built-in protection circuits for high reliability and ruggedness. The AMP4052 is suitable for all single channel modulation standards. It is packaged in a 2.5U Chassis with an approximate weight of 11 kilograms. This System is available with a Digital Monitor & Control upon request. Typical applications for this System are EMI/RFI Testing, Ka band SATCOM and General Millimeter Testing.
-
product
PXI Single 8 Channel Optic Mux FC/APC
40-852-018
The 40-852-018 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Mark II Dual Setpoint Monitor
95006
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
product
Solid State Relays for Switching Heavy Loads in 6-Pin Mini-DIP Package
Series C63
Series C63 solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin mini-DIP package. These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:C63-10 1A, 60Vdc Load; 8-20mAdc Control; through-hole mountedSC63-10 1A, 60Vdc Load; 8-20mAdc Control; surface mounted
-
product
Digital Power and Energy Measurement
EPM 2200
The EPM 2200 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2200 can easily be mounted in a panel for generator monitoring, substation automation and more. The meter can also provide data to RTUs, PLCs and other control devices.
-
product
NI-9147, 4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783496-02
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
product
Analog Control Cable for Electronic Loads
EE105T-xx
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
product
IV-curve Software
Tracer
In Tracer you will find your all-in-one solution for the measurement and elaboration of IV-curve measurements. Tracer is the core application developed by ReRa that will help you to characterize your solar cells and compare the results.Tracer natively supports the control of Keithley 24xx and 26xx sourcemeters.These instruments have proven their strength over time for the measurement of solar cells.
-
product
16-Axis PCIe EtherCAT Master Motion Controller
PCIe-8332
ADLINK PCIe-8332 is a hardware-based EtherCAT motion controller able to support up to 16 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in se...show more -
product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
CompactRIO Chassis
CompactRIO Chassis can add C Series I/O modules to an EtherCAT-, Ethernet- or MXI-Express-compatible system. You can program the onboard FPGA for inline processing, high-speed I/O, and control. You can also use scan mode to quickly expand your real-time system.
-
product
Multifunctional UV Control Software
UVProbe
UVProbe is multifunctional, easy-to-use software supplied as standard with Shimadzu UV-VIS Spectrophotometers. The UVProbe is connected to the LabSolutions system, which is known for its capabilities in complying with ER/ES regulations. Enables safe, reliable management of data.Not only can UV data be managed, but the comprehensive management of LC, GC, and FTIR data can also be accomplished.In addition, When combined with CLASS-Agent, it provides powerful support for Part 11 compatibility.
-
product
ANSI X3.28 to Modbus RTU Converter
Model 2399
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as...show more -
product
Occupational Noise Measurement System
NK122
This Occupational Noise Measurement System is designed to give Health and Safety Managers, or any other professional with responsibilities for managing noise in the workplace, everything they need to protect your workforce from over exposure to noise and to help you ensure your company is complying with The Control of Noise at Work Regulations 2005.
-
product
Control Systems Projects
Precision Development Consulting Inc
Fast Open Loop temperature control system, Batch CVD temperature control system, Single Wafer Temperature control system, Disk Drive Spindle Motor Control, Wafer Indexer Motor Control
-
product
Amplifier
C-Band
Amonics offers polarization maintaining EDFAs for various applications. Including free space communications, coherent beam combining, and detection system. The output light is linearly polarized with high polarization extinction ratio. The compact turnkey benchtop or 19" rackmount instrument incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power adjust control knob and optical connectors. A RS232 or Ethernet computer interface is also equipped.
-
product
Dynamic Micro Ohm Meter
PRIME 600
It is the only micro ohm meter in the market that integrates both the contact resistance and the dynamic resistance measurement (DRM) for cost-efficient condition evaluation of contacts in SF6 and vacuum type circuit breakers; PRIME is a high current micro-ohmmeter that provides true pure DC with smart control up to 600 A, a wide measurement range with high power, dual ground testing process, thermal printer, touch display, pre-defined test modes and automatic reporting.
-
product
Single Frequency CW 532 NM Laser up to 18W
EQUINOX
Equinox is a single frequency, 532 nm continuous wave laser designed for a range of scientific applications including pumping any Ti:Sapphire laser systems. It is engineered to meet the needs of experimentalists requiring high-performance systems with an emphasis on reliability, stability and ease of use. The laser incorporates pump diodes within the central unit and is fully automated with hands-free operation and control via ethernet, webpage and TCP/IP remote interface. This completely sealed...show more
