-
product
Digital Module For Remote I/O
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coup...show more -
product
PC Link Software
LE-PC300R
LE-PC300R is a Windows® software with which you can control the protocol analyzer remotely from a PC and utilize the measurement data of the analyzer on the PC.
-
product
Hyundai Oxygen Sensor
KS60113 - Hyundai
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Dilution-Extractive System
ML675
The Teledyne ML®675 dilution-extractive system can be used in 40CFR75, 40CFR60, 40CFR63, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.
-
product
Three Axis Interferometer
10736A
The Keysight 10736A Three Axis Interferometer is used in multiple axis applications where linear and angular control of the stage is required. It combines in a single package the functionality of an optical bench with multiple beam benders, beam splitters, and three interferometers. The interferometers split an incoming laser beam into three beams to measure linear distance, pitch and yaw, or linear distance, roll and yaw. Three linear measurements provide the basis for calculating two angular m...show more -
product
Advanced Clip-on Thermal Weapon Sight for Warfighter
ThermoSight® T75
Designed to mount on any MIL-STD-1913 rail interface forward of an existing scope, the ThermoSight® T75 offers mission flexibility as a long-range thermal weapon sight and as a hand-held observation device. It’s designed to interface with a wide range of day scopes and weapon platforms. The T75 runs on common AA Li batteries and is equipped with large, rugged controls for image adjustment. The long-wave IR sensor provides crisp imagery all night and all day.
-
product
PXI Dual 2 Channel Fibre Optic SC/PC
40-855-222
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Solution for High Density I/O Applications
BitBox
The BitBox is BitFlow''s new solution for high density I/O applications. Many machine makers require a large number of computer managed I/O signals for continuous control of the system state. This means controlling devices such strobes, solenoids, actuators, indicators etc. as well as gathering inputs from photo-detectors, switches, encoders and triggers. In general, BitFlow frame grabbers come with a fairly large number of inputs and outputs, but for some system this is simply not enough. Most ...show more -
product
Switch & Router Modules
Curtiss-Wright Defense Solutions
Our highly engineered networking cards provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Gigabit, 10 Gigabit, and 40 Gigabit Ethernet. Operating at wire-speed, Ethernet switching and routing can be used to architect the infrastructure for unified (Ethernet only) or hybrid (Ethernet control and other switched data-plane fabric) networks for transferring IP-based control and data packets within advanced military systems.
-
product
Software Abstraction for Easy Control of Digital Multimeters & Multifunction Measurement Devices
DMM
It consists of three modules:- A windows driver which is responsible for the communication and device abstraction- A DLL with NI TestStand Test Steps which allows easy integration in automated production enironments- A standalone executable which simplifies debugging and setup of test sequencesThis architecture allows to open a communication channel from multiple instances to the same device. This is important when for example two channels of a measurement device are used in two independent applications.
-
product
Interface
Renesas offers industry-leading devices to enable efficient and reliable communication for industrial control, networking and computing applications. Dual protocol transceivers, voltage level translators, I2C Buffers, wide operating voltage range RS-232 transceivers, and RS-485/422 devices with the highest noise immunity and ESD protection in small packages are available to support high-speed data transfer and a variety of configurations to fit your applications.
-
product
*High Current Switches
B-1002
Ross High Current Switches are available up to 36,000 amps continuous and over 1,700,000 amps 20µsec RC pulse, with voltage ratings of 6 volts to 400kV peak test. Standard Ross high current switches are built with 80 to 120psi air cylinder actuators. Air cylinder or motor operated for high contact force. Arcing contacts optional for closing current. G-10 epoxy glass laminate is standard insulation on most models. G-7 silicone glass is used on models available for RF applications above 100k...show more -
product
Torque Screwdrivers
From better product quality to a lower total cost of ownership to guaranteed regulatory compliance, you can have it all with market leading Mountz torque screwdrivers. Built-in cam-over mechanisms prevent over and under-torque conditions so you can count on the quality of your work. Assembly and repairs performed with Mountz torque screwdrivers allows any user to deliver precision torque control with confidence regardless of task and operator skill level. And when it's time for compliance inspections or audits, equipment calibration records provide clear documentation. In short, Mountz torque screwdrivers keep your operation tight.
-
product
Fixed-Mount Thermal Camera
FLIR Axxx-Series Smart Sensor
The FLIR Axxx-Series Thermal Smart Sensor Camera has the features automation solution providers need for complex monitoring applications, including critical infrastructure, product quality, and early fire detection. The Smart Sensor configuration includes multiple measurement tools and alarms while also providing computing-on-the-edge, with analytics performed at the camera level for immediate results. With a range of lens choices, motorized focus control, and unrivaled connectivity, A400/A500/A700 cameras offer unmatched power and flexibility. Easy configuration allows you to tailor this monitoring system to your company’s quality, productivity, maintenance, and safety needs.
-
product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Slip-Ring Motor Starting Panels
Rotor Starter
The Slip-Ring Motor Starters are based on the series of resistors that are applied to the rotor circuit to control the speed/torque characteristics of the motor. Rotor starters are mainly used for the motor starting applications requiring high-starting torque like loaded belt conveyors in mining industry. By external resistors, it is possible to shift the motor maximum (break-down) torque up to starting torque point for motors under heavy loads during start-up. The resistors are splitted into ...show more -
product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
product
WAV Trigger
The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the WAV Trigger can play and mix up to 14 stereo tracks simultaneously and independently, with very low latency. Tracks can be controlled via 16 programmable trigger inputs, or by using a native serial control protocol or even MIDI.
-
product
Character Generators
Overlays Text on VideoFront Panel Programmable or via RS232 Computer LinkUp to 32 MCG-2 on one RS232 busGenlocks to either NTSC and PAL automaticallyCharacter/Background Brightness AdjustableFour Character Heights and Four Character WidthsA-Z, 0-9 and Punctuation Marks Character SetBuilt in Menus, Help Screens and Self-testReal Time Clock (RTC) optionRemote Control via RS232 (RJ11 Connector)BNC Video Connectors, 4 Pin MiniDIN on S-VideoTen Pages of Text Storage in MemoryLithium Battery Backup (10 Year Life)Can be powered from external 12Vdc, for Field useCompact Size in a Rugged Aluminum and Steel EnclosureTwo Year Warranty, Made in USA
-
product
Ethernet Gateway for Woodward Easygen Genset Controls and LS-5 And DTSC-200 Controls
ESENET
ESENET is an Ethernet gateway specifically designed to interfaceWoodward's Easygen series genset controls with Modbus/TCP networks. It interfaces via the load sharing CAN bus with the Woodward controls.
-
product
UV Exposure Sources
Standard maintenance, lamp, or filter replacement, does not require any tools. Locking indicator dials on all the system controls, located together for ease of alignment, provide for a reproducible setup. A beam imaging accessory makes alignment even faster.
-
product
PXI Remote Control Module
PXI Remote Control Modules allow direct control of PXI and PXI Express Systems through PCs and laptops. You can choose between copper (up to 10 m) or fiber-optic (up to 200 m) cable that connects to PXI or PXI Express modules in slot 1 of your PXI system.
-
product
DDR3 MSO Probes
The DDR3 DIMM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR3 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR3signals for convenient analog probing.
-
product
Programmable DC Power Supply
SPD1000X Series
SPD1000X Programmable Linear DC Power Supply has a 2.8 inch TFT-LCD display, features remote computer control capability, and real time wave display. This single output design is focused on delivering high performance and ease-of-use in a small package. The SPD1168 features a high precision programmable output capable of delivering up to 16 V/8 A,the SPD1305X features a high precision programmable output capable of delivering up to 30 V/5 A and also includes a 4-wire sense function for more accurate voltage sourcing, especially for long leads or high resistance connections. There are additional output short and overload protect functions to assist in production and development applications.
-
product
Small Fanless 3D Control FAYb Laser Marker
LP-M Series
Panasonic Industrial Devices Sales Company of America
The LP-M series offers a small, fan-less head design with an IP64 protection to prevent dust and water entering from any direction. The 3D Control capability allows marking on various types of products and complicated shapes to meet a large number of application needs. - 20, 50 & 100 Watt Models- Compact IP64 Rated Head- Full 3D Features- Auto Focus capable- Redundant Safety Features
-
product
Smart Control And Development Universal Software
The control software SCADUS (Smart Control And Development Universal Software) is based on Windows operating system. The test control software and test program development and debugging software are done in Delphi. It is designed for a wide base of customers. Each operator and engineer have a separate profile with all screens and software configurations. Online application development is also possible from another computer. The debugger and statistics are offered as standard accessories.
-
product
Modular DC Power Supply
62000B
Chroma Systems Solutions, Inc.
Chroma’s 62000B series of Modular DC Power Supplies offer 5 types of power module with ranging from 1V to 150V, current from 10A to 90A, and offers two mainframe type of six and three position. The six position mainframe can envelop in up to six power modules paralleled operation for 9KW power output. The 62000B can easily parallel up to 14 mainframes to 120KW with current sharing and CAN bus control for bulk power applications.
-
product
PXIe-5644, 6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver
782376-01
6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver—The PXIe‑5644 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5644 features the flexibility of a software defined radio architecture with RF instrument class performance.
-
product
Automated Distortion Characterization and Information System
ADCS
Matrix Test Equipment Incorporated
The Automated Distortion Characterization and Information System (ADCS) is an extension of the Matrix equipment control software that automatically makes RF measurements selected from the following: Cross Modulation (XMOD), Composite Triple Beat (CTB), Composite Second Order (CSO), Carrier to Noise (C/N), Discrete Second Order, Discrete Third Order Distortion. Measurements are made, and the test results and a profile describing the test conditions are saved in a database for later retrieval or reporting.
-
product
Simulators/Threat Emitters
Antennas for RADAR test, simulation and training are designed for integration into complete threat RADAR simulators for use on combat training and test ranges or in simulators for training and evaluation of RADAR operators, aircrews, air-traffic-control or weather radar applications. All antennas for RADAR simulators have high RF power handling capabilities and generally use pressurized transmission lines. Dual-band, single aperture antennas and a cluster of separate antennas mounted to a single pedestal are ideally suited for RADAR simulators in mobile, fixed, shipboard and airborne environments.
