Programmable Oscillators
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-113
-
The 40-297A-113 (PXI) and the 42-297A-113 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
6U Power Supply Mainframe. Accepts Two Programmable Power Modules
GX7400A
-
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
Product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-013
-
The 40-297A-013 (PXI) and the 42-297A-013 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-045
-
The 40-297A-045 (PXI) and the 42-297A-045 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-136-HI
-
The 40-230-136-HI (PXI) and 42-230-136-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
-
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
User Programmable Logic
PCIe-Spartan-VI
-
User Programmable logic - Spartan VI 100 with 40 differential and 12 TTL IO plus PLL(24). 16 DMA ports, to support 8 full duplex byte lanes between the Bus and User FPGAs. Additional GPB interface to support R/W operations to registers etc. Driver and reference SW package includes user defined R/W to User FPGA to support User Architecture without a new driver.
-
Product
1U Programmable DC Power Supply
Chroma 62000E
-
Chroma Systems Solutions, Inc.
Provides a single channel of 1.7kW, 3.4kW, 5kW and three channels of 1.7kW output configured in 1U chassis
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-214-HI
-
The 40-230-214-HI (PXI) and 42-230-214-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-020
-
The 40-254-020 (PXI) and 42-254-020 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 472Ω with 0.125Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Programmable AC/DC Withstanding Volatge And Insulation Tester
RK-7122
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC withstanding volatge and insulation tester
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-112-HI
-
The 40-230-112-HI (PXI) and 42-230-112-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 122Ω with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
-
Product
10-Ch. 0… 5V 400mA Isolated
YAVAP955
-
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
Product
Programmable AC Laboratory Power Supplies, Current-controlled
-
*Fast regulation of the current*Voltage depends on the load*Current and voltage values are configured based on the customer's actual requirements*Power from 250VA to 36kVA*Output voltages 1VAC to 300VAC*Maximum currents up to 2000A per phase
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 1.02k Ohm - SPST
40-294-121
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Voltage Controlled Oscillators
-
Teledyne Microwave Solutions (TMS) offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
Product
2GHz programmable frequency dividerValon
3010a
-
The Valon 3010a accepts a wide range of input frequencies and provides three independent, user-selectable, divided outputs. The 3010a is useful for extending the low-frequency range of any signal source down to 5MHz as a 50Ω output or down to 0Hz as a TTL output.
-
Product
Programmable Industrial PC
HyperPAC
-
The HyperPAC Industrial PC programmable control solution delivers top of the line performance with reliable operation for a variety of control and automation tasks. Compared to standard IPCs, the HyperPAC provides a highly compact, fanless solution, with existing expandable IO via PCIe, along with flexibility to expand and configure the system. The HyperPAC is a flexible, scalable solution for numerous applications and project requirements which enables IIoT (Industrial Internet of Things) integration.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-046-HI
-
The 40-230-046-HI (PXI) and 42-230-046-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 5.806MΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-021-HI
-
The 40-230-021-HI (PXI) and 42-230-021-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-216-HI
-
The 40-230-216-HI (PXI) and 42-230-216-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Programmable DC Electronic Load
DL3000 Series
-
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics, aerospace and fuel cells.
-
Product
Programmable Withstanding Voltage & Insulation Test
LS9923
-
LS9923 programmable withstanding voltage & insulation test system is high-performance testing device special for AC&DC Withstanding Voltage and Insulation Resistance Test, It allows setting the output voltage. The warning value,testing time and some other parameters can be set in the screen.It with a variety of automatic test functions. The testing is quick and high accuracy which is not only applied in the production line but also in the develop research.
-
Product
High Power Programmable AC Source With Transients
-
Chroma Systems Solutions, Inc.
Ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification to quality assurance and mass production
-
Product
Programmable RF Multi-Port Test
-
A programmable multi-port switch between your RF device under test and a Vector Network Analyzer significantly speeds up testing.
-
Product
PCI High Density Resistor Card 10-Channel, 12-Bit, 0 To 4k Ohm
50-295A-121-10/12
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Reference Oscillator
REF Series 1.5” x 1.5” x 0.6”
-
*Connectorized Package *Free Running *Low Phase Noise *Output Power to +12 dBm Available
