Breaker Test Systems
-
Product
RSE Wireless EMC Spurious Emission
TS8996
-
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
4U 8-Slot CompactPCI® System with Redundant Power Supplies
cPCIS-6418U
-
The cPCIS-6418U Series Subsystem is designed for maximum density and has 8 horizontal slots for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
Test Fixture
N1295A
-
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
Product
Wafer Chip Inspection System
7940
-
Chroma 7940 wafer chip inspection system is an automated inspection system for postdiced wafer chip inspection.
-
Product
Data Acquisition System
DAQ973A
-
Get the next-generation data acquisition (DAQ) system with a three-slot mainframe and your choice of nine plug-in modules. Interface with the DAQ using Keysight BenchVue DAQ software or use the intuitive graphical front panel with task-oriented, self-guiding menus.
-
Product
Test Requirements Document (TRD) System
TRD Software
-
The Test Requirements Document (TRD) System helps users develop and document the strategy and structure of test programs.
-
Product
High Temperature Component Test Fixture
16194A
-
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
Advanced SoC/Analog Test System
3650-EX
-
Chroma 3650-EX is specifically designed for high-throughput and high parallel test capabilities to provide the most cost effective solution for fabless, IDM and testing houses.
-
Product
EV Power Components End of Line Test Platform
-
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
Product
Rack based antenna test system
R&S®ATS800R CATR
-
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique rack based CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
RF-Antenna Communication Links Functional Test
-
The application encompasses functional tests of very large quantities of automotive antenna amplifiers, plus parallelization of tests by implementing several test stations in a rotary indexing table. The DUTs are inserted manually and after final assembly, they are loaded into the rotary table; this requires manual triggering by the operator.
-
Product
2m BNC Test Cable
16048D
-
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
Scienlab Combined Battery Test Solution
SL1133A
-
Solution for testing battery cells with an output power up to ±3 kW and a voltage range up to 6 V.
-
Product
Flight Control System Test Platform
-
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Functional Test System
TS-5040
-
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
Product
Communications Test System for Frontline Diagnostics
ATS3000P
-
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Real-Time Operational and Situational Awareness for IoT Systems
Vortex Insight
-
Vortex Insight is a web-based tool that can be used to monitor and manage a Vortex-based system from any location and on any device. It provides views of a Vortex system including statistics associated with DDS entities and system elements active in a live environment. It also provides configurable dashboards for monitoring system behavior through graphs and charts of statistics, including resource usage. Vortex Insight allows users to control the configuration and the QoS of Vortex applications, services and systems.
-
Product
Dielectric Test Fixture
16451B
-
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
-
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
-
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
EOL/Functional Testing
-
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
Product
EVSE Test Platform
-
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
Product
PCI Express 3.0 Test Platform with SMBus Support
-
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
Product
Cobra Temperature Forcing System for ATE/SLT Test Applications
31000R
-
Cobra is the most advanced, compact,powerful temperature-forcing system on the market. Cobra is an adaptable solution to the ever-increasing thermal demands of post silicon validation and device characterization.
-
Product
Single Site Test Handler
3210
-
Chroma Single Site Test Handler 3210 supports various package types such as BGA series, QFP series, QFN, TSOP, and more. The handler is primarily designed for early device design and engineering validation.
-
Product
System Integration
-
G Systems develops fully integrated systems and we know that both software and hardware are equally important to system design. Our focus on code quality and optimization ensures customers receive efficient and maintainable code. We specialize in LabVIEW development and all of our LabVIEW developers are certified developers or architects. We’re also highly skilled in mechanical and electrical hardware design and builds on a wide variety of data acquisition, signal conditioning, RF, and distributed communication platforms.
-
-
Product
Mezzanine System
5047
-
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
Communications System Analyzer
Freedom R8200
-
The Freedom R8200 from Astronics Test Systems represents a major step in the evolution of the Land Mobile Radio Test. The Freedom R8200 is the first and only test instrument that combines comprehensive digital and analog LMR testing with the ability to measure important RF network characteristics, such as Distance to Fault (DTF), Return Loss, and Voltage Standing Wave Ratio (VSWR). The Freedom R8200 is also the only service monitor with the abilityto display advanced RF Parameters in a Smith Chart for more complicated network analysis
