Breaker Test Systems
-
Product
Automatic Test System
Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
Product
Die Test Handler
3112
Test Handler
Chroma 3112 is a productive pick & place handler for high volume single- or multi-site bare die testing.
-
Product
HV Test System up to 20000 Volt
Test System
Insulated test booth with large space for test items. 2 banana sockets for AC connection and 4 banana sockets for the DC connection of the DUTs. IC’s are tested in a long-term test. These are checked in an oil bath so that there are no air gaps to reduce the insulation. Maximum voltage 20 kV. Therefore, insulation tests must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
Product
Application Software for Electronic Test & Instrumentation
test
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
Product
LabVIEW Professional Development System
System
ntegrate hardware from a variety of measurement instruments and devicesIntuitive graphical programming syntax to simplify automationBuild custom user interfaces for engineering applicationsBuilt-in algorithms for signal processing, analysis, math, and PID controlSoftware engineering tools to debug, validate, and deploy codeOne-year SSP membership for technical support, online training, and software upgrades
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Edge AI Inference System
AIR-075
Edge AI Inference System
Edge AI Inference system powered by NVIDIA® Jetson Thor™ Powered by NVIDIA Jetson T5000™ and Jetson T4000™, delivering up to 2070 TFLOPS FP4 inference performance. 19~36V wide power and -10~40 °C wide temp. supported.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
Communications Test System for Frontline Diagnostics
CTS-2750
Test System
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
Smart Aircraft System
System
The Astronics Smart Aircraft System makes that possible. Our patented system enables the immediate, cabin-wide gathering of thousands of data points using sensors & IoT (Internet of Things) technology. The result? You get the insight you need—when you need it. Insight that helps you on every flight. Insight that allows you to improve your operational efficiency, your cabin safety, and your overall passenger experience.
-
Product
EBIRST 200-pin LFH To 104-pin D-type Adapter
93-002-422
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
PXI Functional Test System
U8989A
Functional Test
The TS-8989 PXI functional test system is an integrated, all in one switch, load and measurement system in a box for high voltage or current mechatronics functional test applications of up to 104 nodes and 40A current loads.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Mezzanine System
5041
System
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
Product
Iridium Physical Layer Test Systems
PLTS
Test System
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
Product
CATR Benchtop Antenna Test System
ATS800B
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
test
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
Product
PXIe System Sync Module, 5 Port
M9033A
System Sync Module
The M9033A PXIe System Synchronization Module is a dual-slot, 5-port module that provides multi-module and multi-chassis synchronization and triggering for Keysight's modular instruments.
-
Product
High-Speed Signal Recording Systems
System
GaGe has a long history of providing high-speed, real-time signal acquisition, processing, and recording systems on PC-based platforms. This expertise saves customers time and eliminates uncertainties and risks with self-integrated systems.
-
Product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
Product
EBIRST 50-pin D-type To 37-pin D-type Adapter
93-005-418
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Wireless Device Test
test
New wireless standards, in addition to rising wireless usage, are increasing wireless device complexity while lowering price expectations. To counter rising costs, manufacturers require test systems optimized for efficiency.
-
Product
IOL & Power Cycling Test Systems
Test System
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
Product
EBIRST 78-pin D-type To 68-pin Male SCSI Adapter
93-006-401
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
SoC/Analog Test System
3650-S2
Test System
The Chroma 3650-S2 is specifically designed for high-throughput and high-parallel testing to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
Wafer-Level Parametric Test
test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Product
Development System
PCIe490
System
The PCIe490 Expansion Chassis enables users to scale application workstations with up to eight additional PCIe boards per chassis and up to 63 total slots with chassis daisy chaining. It was designed to accommodate the Abaco Systems PC820 and PC821 with Xilinx Ultrascale technology and multiple FMC+ interfaces.
-
Product
Bloomy Simulation Reference System
System
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
Product
FPD Tester Model
27014
Test Platform
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
